Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - EA5WA

Pages: [1]
Is it possible to make a Yaesu Twin configuration with a pair of standard RRCs?

I would like to help a friend who has a pair of RRC with a Kenwood TS-480 and he wants to move to a Twin system with a pair of FT-2000.

Does he have to change his RRcs?

73 de EA5WA Juan Carlos

Yesterday I've realized that there is 9v on AUX/MIC RJ-45 connector in my Control RRC working in Mode 8 (with RC2000 for Kenwood TS2000) and my MC-80 microphone works, but when I change to another profile in Mode 4, I don't have 9v and my MC-80 doesn't work....

Is it possible to add a checkbox (or similar) on RRC web page to enable/disable that power supply for microphones, in Mode 4?


73's  EA5WA Juan Carlos

Hi there:

Is is possible to control Rotator (COM1) and CAT (COM2) using the same cable conected to the Control RRC mini usb at the same time?

I hardly remember that was possible, but I'm trying to do it (for my friend @ea5zj) and doesn't work.

System is working with two separated cables on control RRC:

  • Mini USB for COM2 (CAT)
  • USB FTDI converter for COM1 (Rotator)

But would be easier and cleaner with only one usb conection for everything....

Is it possible?

73's from EA5WA Juan Carlos

I'm trying to help a friend with a new remoterig installation. Everything is fine, except rotator control.

Prosistel PST641D comes with a mini USB conection por control. Connected with a serial-usb converter to COM-1 on remote side doesn't work.

COM1 on both sides are configured as Mode 3.

Is there anyobdy here using that rotator with remoterig?

We need some help

73's from EA5WA Juan Carlos

General discussion forum / Control with control head
« on: 2013-12-14, 17:57:49 »
Is there a possibility to control any transceiver(like yaesu ft2000) with a control head like the tm-d700? I think it could be necessary a kind of translator between the control head and the RRC at control side, but I'm not sure if it could be possible. Any ideas?


General discussion forum / Using 3G in Spain
« on: 2013-12-09, 23:01:15 »
Hi there:
Only for information (mainly for spanish hams)
Now, finally, my system is working fine.

At Control Side: ADSL 10MB Yacom

At Remote Side: Modem 3g ZTE + Router TP-Link with pre-paid SIM card (eroski movil). Doesn't work with Orange or other virtual operators like Simyo or Masmovil, because they only give you a private IP, not accesible from outside your LAN.

73's de EA5WA Juan Carlos

Hi everywhere:

I'm planning to use the CAT through my remote system, but I have some doubts...

At Control side: I think I must conect PC to the USB conector and Change "Use USB Com port as COM1" to YES. Is not possible to use the COM2? What Mode should I select?

At Radio Side: I want to connect COM2 to the CAT interface in my Icom. Is it possible?

Please, I need a very simple tutorial for my radio, because all the related topics I see are about the K3 configuration.


Configuration, RRC 1258 / Dynamic DNS Status: Error Code 9
« on: 2012-02-01, 17:22:28 »
Hi everyone:

My system is working with ic-706, but only setting the remote side IP external address in the SIP contact Box. It doesn't work neither with dyndns or ddns.remoterig.

I can see in the radio RRC:

Dynamic DNS Status: Error Code 9

DNS status:   OK, =

The Control RRC is always:

DNS status   Error, failed to resolve!

Using the dyndns address I can go into the Radio RRC configuration page, but I can't conect both RRC's.

Any ideas?

73's from EA5EXK Juan Carlos

Hi there:

This is my first topic. I'm just starting to test the system at home, before leave it on the remote site.

I'm trying to simulate the connection using two adsl:

The System now look like this:

adsl1 - PC - Control RRC (conected to the PC ethernet port). I don't have physical access to the router.

adsl2 - Radio RRC (connected to the router).

I have 2 problems:

How can the RRC get an IP connected to the PC?

Another problem is related with ddns.remoterig. Although I changed the ddns server in the configuration, I'm still having access trough instead of ddns.remoterig

Is this ddns server working?

Thanks in advance,

EA5EXK Juan Carlos from Albacete, SPAIN

Pages: [1]