Topics

1

General discussion / No audio packets

« on: 2024-03-03, 02:53:31 »

I am using the 1274A dongle attached to a Windows 11 PC with the 1258MKII at the radio site (Elecraft K3).  I have no audio packets arriving at the PC - the green bar is blank.  I am at my home on the same LAN. 

I also have a Windows 10 PC using the same configuration for both in the RRC and the 1274A and it has audio packets without any problems.  It functions normally within the local LAN or outside.

Does anyone have any ideas as to how I can fix this problem?  Here is a copy of the RRC Status when HRD is connected via the 1274A Com port:

Status

Name   Value
P5.2   OFF
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(45)
SIP command timeout   0
Rx Jitter buffer size   12
Rx Jitter delay   10
Dual Rx   0
Current audio packet size   20
Current audio quality   0 - alaw 8 kHz
External IP   72.93.241.136
SIP Out port   51200
SIP In port   51200
Audio Out port   51201
Audio In port   51201
Command Out port   51202
Command In port   51202
External SIP In port   51200
External Audio In port   51201
External Cmd In port   51202
Other party   192.168.1.152
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status   OK
Ping status (watchdog)   Off
DNS status   OK, remoterig.com = 86.107.103.218
Active profile   Default
PTT status   OFF
Antenna-Switch (IP)   not connected
Common network settings   No

Thanks,

Joe
AJ1Y

2

General discussion / RRC Micro 1274A

« on: 2020-01-11, 03:19:01 »

When I try to connect to my rig using the Remoterig PC Client and the 1274A, it does not connect and I get a message in the line where I see the DNS server name that says "Busy Here."

1. What does that tell me?

2. How do I fix the problem?

Thanks,

Joe

3

Configuration, RRC 1258 / Problems Connecting to M2 RC2800PXAZ

« on: 2016-07-18, 15:32:04 »

We are using Mk1258 RRC at the radio end and the RRC-Micro PC-Client with a K3 and HRD.  The system works fine with the radio. 

The last remaining issue is the connection to the rotor.  The RC2800PXAZ is connected to COM 1 on the Mk1258 RRC at the radio site.  The cable between the RRC and the RS232 port on the rotor is a straight pin to pin cable.  The rotor manual says that the port settings should be

baud rate 9600
bits 8
stop bits 1
parity none
handshake present, but not used

Those are the settings that I applied to the RRC Mk1258 COM 1 in Serial Setup.  Also the rts/cts is 0 and the terminator is 00.  I have tried multiple COM 1 Modes (all unsuccessfully).

On the RRC-Micro PC-Client I set the RRC COM 1 setup to be a variety of modes (none of which have worked) along with aligning it to PC COM 1 (while having radio control on PC COM 2).  I have left the terminator block blank and the timeout at 40 ms.

I then set HRD to connect via PC COM 1 and attempt to connect.  No luck.  I have tried various COM modes on both ends and nothing works.

Since the remainder of the remote setup is working like a champ, I assume that am doing something wrong in the interfaces from the PC thru to the rotor.

Can someone provide some suggestions?

Thanks,