Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - JJ8LNX

Pages: [1]
1
Feature Requests / I can no longer connect
« on: 2024-04-29, 05:00:37 »
Not recently, but for about 3 years now, Nano has been unable to connect.
I purchased a paid app for the IC-7100 and TS-480 and was able to use it for a while, but when the coronavirus started to spread, when I tried to connect, it was connected to the network (the radio was turned on) but No voice or control whatsoever. I can't use either application.
My friend also purchased a separate application to remotely control my radio, but it stopped working around the same time.
Around that time, I contacted them via email, but I didn't hear back from them, so I left it alone, but since a failure occurred in another case, I remembered it and would like to write about it here.
I definitely want a reply.

2
Hardware, Cabling, Installations / Control abnormality
« on: 2024-04-29, 04:53:03 »
Dear
I can no longer connect to two controls.
When the control is connected to a normal LAN and the power is turned on, the LED usually lights up several times before turning on and allowing access, but there is a phenomenon where the LED keeps blinking forever.

I tried resetting the device and reinstalling the latest firmware just to be sure, but the symptoms persist.
When displayed in Setup Manager, the serial and MAC address are displayed, but the IP address etc. are displayed as "0.0.0.0". There is a possibility that the LAN cable has deteriorated, but it is the same even if it is new.

Although they were used in different environments, it seems that both failures were related to Ethernet. I would like to know what measures are effective for this.

I was using 3 controllers, but now I only have one left. I'm worried that it will break soon.

3
Hi

Basically, remote technology of RRC-1258mkII great.
Have a great support to Mike, I was saved. Thanks so much.

But new problem has occurred. Also I want help.

In LAN have a great work.
Delay, good sound, operability, other
I got the same feeling on which the direct manipulation.

But there is a problem if have connected via the Internet.

1. Audio cuts out many times on the way.
2. Suddenly shut down.

Line is the same even in the optical line not only 3G & LTE.
I have moved the RRC-1258mkII RADIO a different house, but was the same.

My RRC-1258mkII is the same as setting the sample settings.
If you want to remotely via the Internet, whether there is a need to change the item?

Thank you.

4
Hi there
Not appear in the display IC-706mkII to recently, but are able to other operations. This is a person who asked about problems.

than mike
Ff the IC-706 can be controlled but the display do not light up, it's beacuse the data signal from the radio to the front panel is not comming trough. Probably caused by a bad soldering in the OPC- cable or a bad red strap in one of the RRC:. s Check with an ohm meter that the red straps LRXD is not broken in one of the units.

And have gotten as answer above, connection confirmation of the strap part was done in ohms meter. The result is good.

I was able to confirm is surely electrical connection from the strap to the end of the OPC-581.

Still results because it does not change, I think you want to the foundation internal electrification verification from the strap.

Electrification verification of LRXD I would like you to tell me whether it is sufficient is can energized to which parts in the printed wiring board.
For example, if it is connected to pin 8 of the Ethernet connector OK.
When it is a different example, if it is connected with 10Ω to ○○ near the power connector OK.

People who suffer from other also the same problem, people who are completely resolved is I have not be found.
I think you want to pursue a thoroughly cause because.

Thank you.


5
Nice to meet you.
First clumsy hard to read in English, or meaning will apologize that it is difficult to understand.
I am using the translation services of google.

Is the main subject.
But already there was a Number of ratings topic to another, you will be drastic solution is (there is also a possibility that did not find) had not been published and did you think was therefore question.
I am in possession of the IC-706mkII of icom, was imported to want a remote control in the RRC-1258mkII.
And to end the set, etc., and also in order to the remote control by pressing the power switch does not all of the LED and the display lights up.
However, send and receive all of the key and VFO dial seems to work.

The OPC-581 that was processed as documentation for using the LAN relay connector, if you directly connect the IC-706mkII and front panel, display and LED will appear as usual.
Change the frequency in that state, and turn it on again via the RRC-1258mkII, results tried tested for transmission and reception and the combined frequency of the other radio machine set to the unbelievably the remote control I was thrilled at the sound quality.
Remote to some extent Turn the VFO in the operation state, it was confirmed that the change is the frequency that had been displayed when you connect again directly. That the operating all other keys etc.

Will probably either of LRXD or LTXD of RRC-1258mkII not connected correctly? We can think that, but we have soldered directly lead solder part of the foundation back.

In manual
Attention! The strapping wires should NOT be soldered
Although was written with, there are several in both places that are not short even plug the many times strap is RRC1258 set into the socket, it was soldered forced directly.
As a result of the soldering, and I now all operations other than the display and LED.

It 's I I was got by an immediate exchange when it was Japan domestic.

Soldering later, but I thought might I have to do something more trouble for the work that went Maybe, you know that there are those who only display also the direction of others does not appear, drastic solution I was let me to think questions and there might.

Now using the Ham Radio Deluxe and I have a remote operation, but has better RRC-1258mkII not mistake even than just voice.
Soon at purchase plan the IC-7100, but I would like to buy to suit a really RRC-1258mkII even when the, you can not buy it scared as long as this problem is not resolved.

I beg you! Solution please tell me!
I also want to use this wonderful system 100%!

What is better to publish my settings, etc.?
If there is to be public information, please it also taught.

Thank you.

Pages: [1]