Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - bigchimp

Pages: [1]
1
General discussion / Micro, 7100, pulsing audio.
« on: 2016-10-15, 08:22:00 »
I'm now looking to order the RRC Micro and working on getting everything running beforehand. I am getting a couple of problems.

In the RRC client the green bar graph is pulsing about once per second, and the RRC light pulses green and a flicker of orange or red in time with the bar graph. When I open HRD and slide the volume the audio pulses in one second busts.

I am getting a UDP cmd status error(0).

The audio out port is normally 13001 with the radio RRC connected and the 7100 head. Everything works fine with this setup. With the RRC client connected the audio output port switches to 13003 and the command Out port to 13004.

Here is the status page from the radioRRC;

Name
Value
P5.2
ON
Connection status
Faulty(See below)
SIP status
Connected/transfering
Last SIP error
None
RTP status
Excellent(60)
UDP cmd status
Error(0)
SIP command timeout
0
Rx Jitter buffer size
7
Rx Jitter delay
6
Dual Rx
0
Current audio packet size
40
Current audio quality
0 - alaw 8 kHz
External IP
173.183.2.92
SIP Out port
13000
SIP In port
13000
Audio Out port
13003
Audio In port
13001
Command Out port
13004
Command In port
13002
External SIP In port
13000
External Audio In port
13001
External Cmd In port
13002
Other party
24.85.226.14
Input 1
High
Input 2
High
Output 0
Low
Output 1
Low
Output 2
Low
Dynamic DNS status
OK
Ping status (watchdog)
Off
DNS status
OK, remoterig.com = 213.180.92.125
Active profile
7100 Base
PTT status
OFF
Antenna-Switch (IP)
not connected
Common network settings
No
System messages
No

My system is Windows10. I followed the instructions on another posting for the Microbit device manager and was not able to get a resolution.

Any assistance will be appreciated.

Ian
Vancouver

2
Feature Requests / Icom full features
« on: 2016-08-19, 00:23:17 »
I continue for the most part to be very pleased with the remoterig with my 7100. Originally I used the app during the trial period.

I found however I didn't feel the app was worth purchasing as many key features were not available. Many of these features have been requested already and I understand there is a process to development of the app and other priorities for the developers.

I do look forward to seeing a more full featured version of the app that would allow use of my radio with my auto tuner function and also access to the many pre-programmed memories, for use both HF and importantly VHF/UHF (repeaters).

The app now is a bit of a novelty, but is so limited it is not particularly useable.

Are there plans to expand the capability of the app with more features? I know others have expressed this. With such a great product it would be exciting to be able to use the system to its full capability.

Ian
Vancouver, BC




3
My 7100 reboots on transmit after a few seconds mostly on HF, and also VHF / UHF. The remoterig also acts like it is power cycling with a full reboot.

I thought RF was the issue as it rebooted constantly. Eventually I figured out that this happened only on my favorite screen with all meters up on the screen. If I change to any other screen the system does not reboot.

For several months now I have avoided the screen with all meters visible and not a single reboot!

I have no idea why this particular screen sees the reboot problem but no problem on other screens. This happens remote and also on the LAN.

I would like to figure this out so any theories are appreciated.

My system is heavily decoupled in all respects, and I can say with some confidence that stray RF in my system is not an issue.

My setup does continue to disconnect and restart on receive occasionally, but the internet connection may be the fault there.

Any ideas welcome.

Ian
Vancouver BC

4
General discussion forum / RRC 1258 reboots on wifi
« on: 2016-03-03, 20:19:55 »
I am operating an IC-7100 with the display connected to the RRC1258 control and wifi module installed.

Lately the RRC1258 reboots occasionally while receiving and often while transmitting. It appears to power cycle. The interesting part is that is only does this on WIFI.

The reboot happens when on my home wifi (LAN) or remote (WAN). If I connect the RRC1258 control through a cat5 cable to a router, the system does not reboot and appears to operate normally.

I did update the firmware with the new CW pot profile select version 2.89.

I will try re-loading the firmware. Any ideas otherwise?

Ian
Vancouver

5
Feature Requests / 7100
« on: 2015-11-12, 05:40:06 »
My new RRC's and app are working nicely with the 7100. Thanks for a great product!

For the 7100 my Nano wish list would be;

Tune button operation
Access to memories for repeater operation
Power settings

....and bluetooth headeset please.

For the RRC control it would be nice if the profiles could be linked to a particular network so manual switching was not required. A minor thing, but this would make portable operation seamless.

Thanks,

Ian
Vancouver BC

Pages: [1]