Messages

1

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-10, 22:24:21 »

MMMMMMMMMMMMMMM...........................

what you think..You can check my radio box from remote??
Last chance - if not working I retourn the box to you for a factory check

Franco i1fqh

2

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-09, 11:11:02 »

Yes done....same problem..
Attention when switch ON on remote no Volt(pin8) on radio acc when switch OFF on remore 4.7 volt (on PIN8) radio acc pin..

We need also 4.7 volt to switch On the radio or not???

Franco

3

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-08, 22:15:34 »

Ok g.e.Mike

When remote power switch "on" no volt on pin 8 acc. connector of radio - when send "off" read 4,7 volt on pin 8 and radio goes off
 
Franco i1fqh

4

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-05, 22:18:54 »

G.e.Mike....

still here..

YES when I press the PWR  button on the Control-K3 the yellow LED on the AUX/MIC connectors (radio controll) goes ON (not the red)

 -Status Output 0 change from low to high

but radio remain off..

Franco


Status of the "radio" remain OFF also when radio is ON

5

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-05, 00:13:50 »

OK now zzzzzzzzzzzzzzzzzzzz...............


Tnx and good night
Franco i1fqh
73

6

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-04, 23:19:04 »

I opened the radio...difficult (impossible) to measure volt on pin 8.. No other way??

Setting check

CONTROLL IO settings

IN0 mode          l/0
OUT0 mode     l/0   
OUT1 mode     l/0
OUT2 mode   l/0
USB RTS as PTT  DISABLED
   
USB DTR as CW DISABLED


-----------------------------------------------

RADIO CONTROLL IO SETTING

OUT0 mode   CONNECT
OUT0 on/off   OFF
    
OUT1 mode   CONNECT
OUT1 on/off   OFF
    
OUT2 mode   CONNECT
OUT2 on/off   OFF

All  OK??

7

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-04, 22:50:40 »

Yes is on the back of the radio but pin 7 of the radio ACC it is not phisically connected to the RRC through the cable..
If I not mistaken cable E3c use only pin 1,8,5

OK I have to measure if voltage on pin 7 of the rear ACC radio  connector goes LOW...How Low?

Tnx
Franco

I remenber the problem - Remote radio do not goes On but goes OFF

8

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-04, 22:23:08 »

You  can measure with a volt meter that pin 7 in the ACC connector goes low, but it's open collector


Hello Mike g.e.

but pin 7 in the ACC connector as seen on page 207 of the user manual is not in use ... cable use pin 1-8-5

Tnx
Franco i1fqh

9

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-03, 23:49:05 »

Hello Mike

bought new from you on 2012 - serial n.r. 1258 (twin k3 set with all cables.)
Never used (busy with my work) only tested 1 time -----

Tomorrow evening I try to test with a volt meter pin 7

Tnx and good night

73 Franco

10

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-03, 22:59:36 »

The hardware signal is only for power ON.

What I have to do to test if hardware works properly??



 Power off is handled by a data message over the CAT port

OFF is OK!

11

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-03, 21:44:24 »

Tnx

"On and off" on remote is done by same cable?

Now i will test the cable connections. (Tested is OK!!)

No particular hardware setup on the board??

Franco i1fqh 

P.S.

All 2 radios are connected but
RADIO STATUS
is
Name   Value
Radio   OFF
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None

why Radio OFF???Radio is ON!

12

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-03, 20:18:35 »

MMMMMMMMMMMMMMMM

tnx Mike for support

Cable is the original supplied and in use..

set of: Out0 = Connect

But remote do not switch on the radio...
Any idea?

Franco i1fqh

13

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-02, 23:37:25 »

Ok tnx DONE now I see 1 radio and 1 control (before 2 control)

Tnx very much......

It appears to be working---

last problem (sure not least)

Control switch off remote radio but non on?

Tnx Franco i1fqh

14

General discussion forum / Re: K3 + K3 and no connession

« on: 2014-02-02, 16:49:16 »

Ok tanks Mike for quick reply

and pse exact serial setting is
On:

Remote
COM 1 - Mode 7

Local
Com 1 - Mode 6

?

73 Franco

15

General discussion forum / K3 + K3 and no connession

« on: 2014-02-02, 15:25:07 »

GooD morning OM

Before to go crazy I am writing to solve my "Remoterig" problem
2 Elecraft K3 connected to the network via a home router
These are the radio setting
-------------------------------------------------------------------------
RADIO

Radio settings

Program mode   Elecraft twin
Sip password   no passw.
Sip contact   192.168.0.227
Auto connect   no
Audio quality   
Codec out gain   
Codec inp gain   
Codec inp HPF Hz   
Codec inp preamp   38400
COM0 baudrate   8
COM0 data bits   1
COM0 stop bits   0
COM0 parity           2
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0 no

Status
Name   Value
Control panel   ON
Radio   ON
Connection status   Disconnected
SIP status   Unknown(1)
Last SIP error   None
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   0   
------------------------------------------------------------------------------------------
CONTROL SETTING

Program mode   K3 TWIN
Sip password   NOPASSWORD
Sip contact 192.168.0.228   
Auto connect   NO
Audio quality   
Codec out gain   
Codec inp gain   
Codec inp HPF Hz   
Codec inp preamp   
COM0 baudrate   38400
COM0 data bits   8
COM0 stop bits   0
COM0 parity           1
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0                  NO

Status
Name   Value
Control panel   ON
Radio   ON
Connection status   Disconnected
SIP status   Connect request
Last SIP error   None
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   0

----------------------------------------------------------------------------



Why they do not connect?
thanks

73 Franco I1FQH

i1fqh@yahoo.it