Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - N4QS

Pages: [1]
1
Configuration, RRC 1258 / AF volume problem with K3 twins
« on: 2024-04-25, 17:25:40 »
I have been running RemoteRig twin boxes with a mini K3(0) and a remote K3 for many years.  I have always had a problem with the AF volume becoming almost zero whenever I change modes or reconnect the logging program at the control end.  In order to restore volume, I have to turn the AF volume control on the mini down to zero and the back up to its normal position.  The volume is then restored.  Can anyone tell me if this can be fixed with a setting change?  I am wondering if I happen to have some setting not set correctly.  Any other way to fix the problem would also be appreciated.  Thank you.  73,  Dave, N4QS

2
Mike,

I got it working.  Turns out it was a cabling issue with the K3.  Thanks for the help on port forwarding.

73,

Dave, N4QS

3
Mike, I changed my ports for the second Radio RRC to 13102, 13101 and 13100.  Now I can turn on the radio from the control K3(0) mini, but the mini then goes into Term mode.  No control of radio and no audio.  I assume that means the SIP port is working -- 13100.  But why are the cmd and audio ports not working?  Any thoughts?  I have port forwarded all three ports in the router.  Dave, N4QS

4
Thanks Mike.  That's what I thought.  Do you also have to have different Web Server ports?  The user manual says that the web and telnet ports have to be different for each Radio RRC.  Is that correct?

Dave, N4QS

5
I have been using RRC1258 Elecraft twins successfully for many years.  I would now like to install a second Radio RRC at a second operating position at my remote farm location.  They would both be part of the same LAN.  The first Radio RRC is setup as 192.168.0.228 and I setup the second Radio RRC as 192.168.0.227.  In the second Radio RRC what port numbers do I use under Advanced settings.  Can I use the same (default) ports as I do in the first Radio RRC?  13002, 13001 and 1300?  Or do I have to change these ports to not conflict with the first Radio RRC?  If so, what port numbers should I use?  So far I cannot get my Control RRC to sync with the second Radio RRC.  Thanks in advance for any assistance.  73,  Dave, N4QS

6
To all,

I have been running RemoteRig Twin boxes for my K3 for many years.  I normally run N1MM at the control site and use one of the RemoteRig com ports to key cw.  Works great.  But now we would like to run N1MM at the radio site using a remote viewer like Splashtop or TightVNC.  I would still like to use the paddle at the control site connected to the K3(0) mini, but we would like the use the function keys within N1MM (running at the radio site) to also send CW as needed.  Is there a way to do this?  Thank you.  73,  Dave, N4QS

7
I would like to operate two K3(0) minis remotely in SO2R mode.  Is it possible to connect two RemoteRig control boxes to the same PC?  I assume each box would need to setup its own unique set of virtual com ports.  I have been using one K3(0) mini to connect to a remote K3 using the RemoteRig Twins for several years.  Works very well.  I would now like to add another K3(0) mini to connect to a different K3 at the remote site.  Has anyone done that?  Thank you.  Dave, N4QS

8
To all,

I currently use a K3(0) mini to connect to a remote K3 using the K3 remoterig twin boxes.  I have a spare K3 that I would like to use as a second control from a different location (my office).  I am wondering if two controls can be connected to the same remote at the same time?  If not, do I need to disconnect the K3(0) mini or power it down when I want to use the spare K3 as the control at the other location?  Can I leave both control remoterig boxes powered on if the K3(0) or the spare control K3 not being used are powered off?  Any suggestions or references on how to do this would be appreciated.  73,  Dave, N4QS

Pages: [1]