Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - n2rd

Pages: [1]
1
Configuration, RRC 1258 / Extra CAT on Remote Control end
« on: 2021-06-28, 19:10:54 »
Dear all,
  I have been using OmniRig along with Log4OM and WSJT-X on the remote end with a K3/Mini twin configuration.  This does not seem reliable.  Is there a way to get parallel CAT on the remote end for use with a logger and WSJT-X at the same time?
Thanks,
Raj, N2RD

2
General discussion forum / Setup issue
« on: 2020-09-22, 03:57:32 »
Please help with RRC setup.
I have a K3 (upgraded with KIO3B) and K3/0.  I have not been able to connect the K3/0 with K3 using the RRC units.  Here are the copies of the status pages:
Remote:
Name   Value
P5.2   OFF
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(16)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   1
Current audio packet size   20
Current audio quality   2 - Linear 16 bits 8 kHz
External IP   192.168.1.170
SIP Out port   13000
SIP In port   13000
Audio Out port   13001
Audio In port   13001
Command Out port   13002
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   192.168.1.169
Other party(mac)   00:1e:fd:01:92:30
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status   Unknown
Ping status (watchdog)   Off
DNS status   OK, remoterig.com = 213.180.92.125
Active profile   Default
PTT status   OFF
Antenna-Switch (IP)   not connected
Common network settings   Yes

Control:
Name   Value
P5.4   OFF
Radio   OFF
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(31)
SIP command timeout   0
Rx Jitter buffer size   12
Rx Jitter delay   8
Dual Rx   0
Current audio packet size   20
Current audio quality   2 - Linear 16 bits 8 kHz
SIP Out port   13000
SIP In port   13000
Audio Out port   13001
Audio In port   13001
Command Out port   13002
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   192.168.1.170
Input 0   High
Input 1   High
Input 2   High
Output 0   High
Output 1   Low
Output 2   Low
DNS status   OK, remoterig.com = 213.180.92.125
Active profile   Default
PTT status   OFF
Common network settings   No

All my cabling is in place except for the I/O on the remote site. 
I do not know what p5.2 off, p5.4 off and radio off mean.

Any help appreciated.
Thanks,
Raj, N2RD

3
General discussion forum / Control unit on remote site
« on: 2020-09-05, 21:28:58 »
Dear all,

  I bought some used elecraft remote systems and ended with two control units.  I want to use with a K3s and K3/0 mini.

Can I configure a control unit (one with CW knob) to be a remote site unit and use it with the K3s?

Details:
older unit control version 05 hw 006 (latest firmware 2.95)
newer unit also control version 07 hw 008 (also with latest firmware 2.95)

Thanks for help,
Raj, N2RD

Pages: [1]