Messages

1

Configuration of Routers, Firewalls, etc / Re: STARLINK PERSONAL & K3/0 Mini

« on: 2025-01-28, 13:41:02 »

Hello Guys

I finally got the solution from other guy that know about networking, Staarlink, etc.

I just need to change Starlink Plan to have a public IPv4 politic

thanks!

Jorge

2

Configuration of Routers, Firewalls, etc / Re: STARLINK PERSONAL & K3/0 Mini

« on: 2025-01-15, 23:09:41 »

hello Mike

Ubiquiti link is very hard to maintain (6 antennas).

Do you know if Starlink Business plan will work?

thanks
Jorge

3

Configuration of Routers, Firewalls, etc / STARLINK PERSONAL & K3/0 Mini

« on: 2025-01-15, 16:36:52 »

Hello

for many years I have a pair of RRC 1258 boxes workng with a K3/100 on the radio site and a K3/ mini on the control side, all working perfectly

The internet on the radio site, is from a link with Ubiquiti antennas from my home, so I am in the same network

NOW I change the ubiquiti link with a Starlink antenna, PERSONAL PLAN, at the radio site.

What type of routers or other hardware I need to have the remote working with the Starlink PERSONAL PLAN at the radio site and the local internet at home?

I have no idea of networks or VPN. But the locals guys that do these work donīt have idea of amateur radio, so what I need to tell him so he can figure out what hardware I need to buy or what he need to setup?

thanks in advance!!

73,
Jorge
CX6VM/CW5W

4

Configuration, RRC 1258 / RRC1258-MkII RJ45 AUX/MIC leds blinking - burned?

« on: 2024-11-13, 19:30:26 »

hello

continuing with my station problems, today I noriced that the remoterig box at the remote side is not working.

I bring it at home to test it, connected to power and the red and yellow leds on the RJ45 AUX/MIC are blinking

I connected it to Microbit setup manager and I read a text in red "look ForHids()"

I do GET FROM DEVICE and nothing happen

Any idea whatīs the problem and how to solve it?

thanks in advance!!

73,
Jorge
CX6VM/CW5W

5

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-12, 00:22:44 »

Mike

I remember that sometime ago when my internet link was broken, I use a Movistar router, it worked, I just needed to setup a dydns to have it working

I will ask a friend to set it up for me.

thanks!
Jorge

6

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-10, 16:04:34 »

thanks Mike

this is very bad news for me :-(

73,
Jorge

7

Configuration, RRC 1258 / RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-06, 20:58:31 »

Hello

after many years using RRC1258-MkII on the same network (with an internet link from my house to the remote site), now I will move to Starlink on the remote site.

My network use 192.168.0.x addresses, and my remoterig boxes use 192.168.0.169 and 192.168.0.170

My new network on the remote site, with Starlink and a router, use 192.168.10.x

So my question is how I need to setup the remoterig and routers to have remoterig working? With 192.168.0.x on the home and 192.168.10.x on the remote side

thanks in advance

73,
Jorge
CX6VM/CW5W

8

General discussion forum / Re: RRC1258, K3/0 mini no RF output on any mode

« on: 2024-03-08, 02:19:34 »

thanks Mike

tomorrow will go to the remote site and check what happen

73,
Jorge

9

General discussion forum / Re: Mitch - DJ0QN SK

« on: 2024-02-29, 22:55:59 »

just know about this, very sad news

a great guy, always helping in this forum

RIP

73,
Jorge
CX6VM/CW5W

10

General discussion forum / RRC1258, K3/0 mini no RF output on any mode

« on: 2024-02-29, 22:11:45 »

Hello

today i noticed that my K3/0 mini is not transmitting on any mode, SSB, CW, FT8

Radio go on TX, but no RF output

I can receive without problem on SSB, CW and also FT8, but incredible that I cannot transmmit

Any idea what to check?, MIC gain is OK, POWER is OK

thanks
Jorge
CX6VM/CW5W

11

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-11-08, 20:36:34 »

Hello Mike

yes, I have the original Elecraft cables

today I finally set MIC SEL to rP.H, this was the way to do FT8 that also was not working yesterday after the changes I did

I am emailing both files to you

thanks!

Jorge

12

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-11-08, 01:06:33 »

hello

finally I have time to go to the remote site

I took MH2 Elecraft microphone

I tested on local K3, a radio that is alone to do radio directly from the contest station, and it works OK.

Then I connected the MH2 on the K3 that I use to do remote, it was ON and MH2 was working perfectly, going full power output

Then I arrive at home, connected the MH2 microphone on the K3/0 mini, and doesnīt work?

No idea what is wrong

Bottom of the line, now I cannot TX on FT8!, I need to review what I modify on the K3 menu that is not TX. Radio go on TX but no output

thanks!
Jorge
CX6VM/CW5W

13

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-10-11, 00:03:32 »

Hello

I imported a good setting files on each RRC1258 boxes.

Maybe the audio cable on the remote side is disconnected?

Donīt know what more to check in my side

73,
Jorge
CX6VM

14

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-10-10, 18:12:32 »

hello Mike

I tried with all options

MIC SEL = rP.H
MIC SEL = LInE In
MIC SEL = FP.H bIAS

etc

73,
Jorge

15

Konfiguration av RRC 1258 / RRC1258, K3/0 mini no SSB output

« on: 2023-10-10, 02:52:50 »

Hello

My setup with K3/0Mini and remoterig boxes was working fine

Now after some months not doing a phone qso, I tried again but no audio out. I am usinh MH2 microphone with the K3/0 mini. I can see my amplifier client showing 1200 watts, but no ALC bars on K3 display, I was monitoring me but not listening my voice.

I had some storaged messages on K3īs M1, M2, M3 and M4 memories and the work OK, perfect output audio showing ALC bars on my K3 display

Any idea what may I check?

thanks!

Jorge
CX6VM