16
General discussion forum / Re: Use COM port without RADIO
« on: 2013-01-20, 17:49:09 »
OK!
Thank you
73 hb9edm
Thank you
73 hb9edm
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
General discussion forum / Re: Use COM port without RADIO
« on: 2013-01-20, 12:32:28 »
Hi Mike,
There are at least two reasons why this option can be interesting:
1) remote site where you have to pay attention to the power consumption (solar panel..)
2) if you have problems with a radio can NOT even handle other devices attached to the com ports and use it, if necessary, with a second radio
Do you think it possible to establish the link between the two remoterig without having to turn on the radio or change the settings?
I noticed that if on the remote site the power supply of the ts 480 is off, but I try to turn the radio on, the connection between the two remoterig is successful and I can use the com ports....
73
HB9EDM
There are at least two reasons why this option can be interesting:
1) remote site where you have to pay attention to the power consumption (solar panel..)
2) if you have problems with a radio can NOT even handle other devices attached to the com ports and use it, if necessary, with a second radio
Do you think it possible to establish the link between the two remoterig without having to turn on the radio or change the settings?
I noticed that if on the remote site the power supply of the ts 480 is off, but I try to turn the radio on, the connection between the two remoterig is successful and I can use the com ports....
73
HB9EDM
18
General discussion forum / Re: Use COM port without RADIO
« on: 2013-01-17, 14:24:21 »
OK now is more clear.
My radio TS480...
I need to power on my amplifier to use it with my second radio that is connected to a computer to be remoted.....
There are no way to begin the connection without power on the radio?
It will be a very nice feature
thks
HB9EDM
My radio TS480...
I need to power on my amplifier to use it with my second radio that is connected to a computer to be remoted.....
There are no way to begin the connection without power on the radio?
It will be a very nice feature
thks
HB9EDM
19
General discussion forum / Re: Use COM port without RADIO
« on: 2013-01-17, 14:12:51 »
Hi Mike!
Strange, if I don't turn on the radio the LED over MIC/AUX is off.
How can I do that without powering ON the radio?
Now I have my radio ON and my amplifier too. On my screen I can see the expert sw to manager the ampli.
Now If I turn OFF the radio the sw say no connection and I can't use it.
Strange, if I don't turn on the radio the LED over MIC/AUX is off.
How can I do that without powering ON the radio?
Now I have my radio ON and my amplifier too. On my screen I can see the expert sw to manager the ampli.
Now If I turn OFF the radio the sw say no connection and I can't use it.
20
General discussion forum / Use COM port without RADIO
« on: 2013-01-17, 13:48:52 »
Hi!
I would like to know if is possibile to use the COM port, for example to manage an amplifier or rotator, without the need to turn ON the radio.
I have tried with my Expert 1k but if I don't turn on the radio the amplifier won't be visibile via remote software.
Wrong cable connection?
thks
I would like to know if is possibile to use the COM port, for example to manage an amplifier or rotator, without the need to turn ON the radio.
I have tried with my Expert 1k but if I don't turn on the radio the amplifier won't be visibile via remote software.
Wrong cable connection?
thks
21
General discussion forum / Re: Hum Problem with 2.35 and USB COM2
« on: 2011-04-18, 20:00:03 »
Jan!
ehm.... ok, my mistake!
I thought it was possible to use it as an additional COM port for PTT...
ehm.... ok, my mistake!
I thought it was possible to use it as an additional COM port for PTT...
22
General discussion forum / Re: Hum Problem with 2.35 and USB COM2
« on: 2011-04-17, 13:17:53 »
hello!
On my setup I'm using COM2 to control my rotator.
With "Use USB Com Port as COM2" parameter the COM2 stop working.
fw:
2.36
com2 settings:
com2 mode -> Mode 3, char-timeout
com2 baudrate -> 4800
com2 data bits -> 8
com2 stop bits -> 1
com2 parity -> 0 - off
com2 terminator -> 0d
On my setup I'm using COM2 to control my rotator.
With "Use USB Com Port as COM2" parameter the COM2 stop working.
fw:
2.36
com2 settings:
com2 mode -> Mode 3, char-timeout
com2 baudrate -> 4800
com2 data bits -> 8
com2 stop bits -> 1
com2 parity -> 0 - off
com2 terminator -> 0d
23
General discussion forum / Re: TS-480 and signalink
« on: 2011-01-09, 12:21:25 »
Hi Geir!
thks for your post!
I will buy the signalink and share with you my impression.
Now I have to solve another problem. In my configuration I have all the com port used (rotator and amplifier) and I have to choose how to get the CAT connection from the 480. A pc on the remote side? A rs-232 over ip adapter? or....
Do you have any idea?
Best 73
thks for your post!
I will buy the signalink and share with you my impression.
Now I have to solve another problem. In my configuration I have all the com port used (rotator and amplifier) and I have to choose how to get the CAT connection from the 480. A pc on the remote side? A rs-232 over ip adapter? or....
Do you have any idea?
Best 73
24
General discussion forum / TS-480 and signalink
« on: 2011-01-05, 12:02:49 »
I'dlike to know if someone has already connected signalink to the TS-480 but directly to the display (RCC-client side) like described for icom 706 (http://www.remoterig.com/en/digital.htm)
Is it a possible setup or it's a must to put the signalink on the radio side?
Configuration?
Impression?
Thks in advance
HB9EDM
Is it a possible setup or it's a must to put the signalink on the radio side?
Configuration?
Impression?
Thks in advance
HB9EDM
25
General discussion forum / firmware 2.21 - unstable?
« on: 2010-10-17, 14:11:26 »
Hello everyone,
Since I installed the 2.21 firmware the connection between the two remoterig seems more unstable.
Problems renewing ip via dyndns, disconnection during transmission, problem to see the webpage...
Is it me or others have noticed these problems?
73 de HB9EDMarco
Since I installed the 2.21 firmware the connection between the two remoterig seems more unstable.
Problems renewing ip via dyndns, disconnection during transmission, problem to see the webpage...
Is it me or others have noticed these problems?
73 de HB9EDMarco
26
General discussion forum / Re: Complete TS-480 Setup with many options
« on: 2010-09-21, 21:34:34 »
Hi Guy!!!
Congratulation for your complete setup!
I will copy you :-)
Best 73
Congratulation for your complete setup!
I will copy you :-)
Best 73
27
General discussion forum / Re: Easy Rotator Control
« on: 2010-09-05, 21:12:34 »
Hi!
strange problem.
ERC is used with which rotator?
Port settings are corrected?
Eventually you can try with other software like hrd rotator.
strange problem.
ERC is used with which rotator?
Port settings are corrected?
Eventually you can try with other software like hrd rotator.
28
General discussion forum / Re: Easy Rotator Control
« on: 2010-09-04, 09:19:19 »
Hi!
On the remoterig the com2 is male. The cable used from the ERC and the remoterig is jack to rs232 female.
No adapter.
Best 73
HB9EDM
On the remoterig the com2 is male. The cable used from the ERC and the remoterig is jack to rs232 female.
No adapter.
Best 73
HB9EDM
29
General discussion forum / Re: I'd like RRC-Micro PC-Client but...
« on: 2010-08-11, 22:51:41 »
Hi Guy!
thks for the info!
best 73
thks for the info!
best 73
30
General discussion forum / Re: I'd like RRC-Micro PC-Client but...
« on: 2010-08-11, 08:01:33 »
TTL for the display
COM1 for the amplifier
COM2 for the rotator control
no more ports available, no CAT so no PC-client connection possible.
Best 73
hb9edm
COM1 for the amplifier
COM2 for the rotator control
no more ports available, no CAT so no PC-client connection possible.
Best 73
hb9edm