Messages

31

General discussion forum / Re: I'd like RRC-Micro PC-Client but...

« on: 2010-08-10, 13:44:43 »

Hi Guy,

I don't understand your reply.
Now, with my setup, I can't use the rrc-micro client because my radio is not connected with cat on the remoterig so.... NO pc-client for my shack.

32

General discussion forum / I'd like RRC-Micro PC-Client but...

« on: 2010-07-29, 23:06:03 »

...How can I use it if I have both com port already in use?

I have the mkII version and the ts-480.
The com 1 is used for the amplifier and the com 2 is used for the rotator control.

I'm very interested on the rrc-micro but I don't want to sacrifice the amplifier or the rotator, any idea to solve this problem?


Best 73

HB9EDM

33

General discussion forum / Re: TS-480, Expert 1k, ERC

« on: 2010-07-11, 22:29:04 »

Hi Mike!

absolutely no problem! All is working fine.

My post was just an information for the connection with the ERC (Easy Rotator Control) and the remoterig via COM2.

I change the thread.

34

General discussion forum / Easy Rotator Control

« on: 2010-07-11, 18:07:30 »

Hi!

This post just to inform how to connect the ERC on the COM2

- The Expert 1k use the configuration written on the "Power Amp/rotators" section. It use the COM1

- The ERC (rotator control with yaesu G1000 DXC) use this configuration (COM2):

mode                        3 - char timeout
COM2 baudrate             4800
COM2 data bits              8
COM2 stop bits              1
COM2 parity              0-off
COM2 terminator (hex)   0d

ERC-cable at the radio site, straight cable at the control site (thsk HB9AZT)

I hope that this post can help.


best 73

hb9edm


P.S the ERC interface is very good, the support is fantastic! thks Rene

35

General discussion forum / audio noise when the radio i poweroff

« on: 2010-04-27, 07:47:43 »

Hello!

I noticed a noise sound (on the remote side) when are turned on the two remoterig. (radio is poweroff)
Then this noise stay also during when I poweron the radio but is more present when the volume is low.

Any suggestion?


radio: FT2000
remoterig: RRC-1258 (MkII)

best 73
HB9EDM

36

General discussion forum / Re: PCC-2000 to control FT-2000 via RRC 1258MkII - any positive results?

« on: 2010-04-20, 22:14:12 »

Hi Andy!

I'm using without problem PCC and HamRadioDeluxe with FT2000.

The version of PCC-2000 is the last one (1,42).

Which type of problem do you have?


Best  73

HB9EDM

37

General discussion forum / radio on tx without powered remoterig

« on: 2010-03-25, 08:13:11 »

Hello!

My setup:
remoterig MKII and FT2000


When I turn on the radio at the remote side (manual operation) with the remoterig attached (mic + audio) but NOT powered, the radio begin TX. When I power on the remoterig the radio stop tx and it can be used normally.

All the system works on LAN.

Is it a normal situation?

Best regards

38

General discussion forum / New version for remoterig?

« on: 2009-12-09, 11:57:38 »

Hello!

It's planned to release a new version for the remoterig?
Features?


I read this info on the homepage:

Sale ! The second version of Remoterig is on the way so I sell the remaining few ex for EUR 325.
(there is only a few sets left so they can be sold out even if you get an automatic confirmation)

Best 73

39

General discussion forum / remoterig with two different radio...

« on: 2009-11-01, 20:13:41 »

Hi!

I would like to control my FT2000 remotely with remoterig but without using a pc on the client side as describe on the "yaesu config".

Is possibile to have on the client side a FT857 with remoterig and on the "server" side another remoterig attached to FT2000?

The only thing that I want is to be able to change frequency with the knob vfo and to press the ptt on the mic attached to the FT857.

Best regards

Mount