Messages

46

General discussion forum / Re: N1MM+ CW Speed Control: RRC Winkey emulator and CW speed with paddle into RRC

« on: 2018-10-30, 22:11:23 »

Jorge

If you are using a K3/0, it is easy to add an outboard Winkey.  I stopped using the RR Winkey- I found it was too fussy, and I lost connectivity to it to many times.  I added a MORTTY keyer (for $18), configured it in N1MM+, and the cable goes from the output of the keyer to the KEY jack on the back of the K3/0.  Now you can plug the paddle into the RR paddle input, set one speed there, and use the MORTTY interfaced with N1MM+ for a different speed.  Or, if you want both speeds the same, plug the paddle into the MORTTY keyer.  Works FB.

Dennis W1UE

47

Hardware, Cabling, Installations / Using an outboard Winkey with RR unit

« on: 2018-10-26, 20:02:48 »

I've looked through the documentation for the RR units, and am not quite sure of the best way to do this.  I want to use an outboard Winkey (not the RR Winkey unit) to key CW.  Is there any "easy" way to do this, such as just turning off the RR keyer?  How about keying through a cable for the Aux/Mike input?

Dennis W1UE

48

General discussion forum / Re: Random connection problem

« on: 2018-06-12, 19:02:30 »

Steve- I had some of the same problems that you have.  Sometimes it would connect, sometimes it wouldn't connect.  Sometimes it would connect and work for awhile, then lose connection and stop working.  In my RRC Control unit, I had it set for a static IP address.  There were no conflicts- it had its own IP address.  I changed that to a DHCP IP address, and let the router assign it.  My connection problem was now gone.

Don't ask me why, but that was all it took.  I couldn't correspond the change with any new router firmware, Win10 update, or Internet changes- but that fixed the problem.  YMMV.

Dennis W1UE

49

Hardware, Cabling, Installations / Re: Constant audio level from Conrol RRC to Signalink for morse decoding...?

« on: 2018-03-11, 12:49:32 »

I have never used a Signallink, so I don't know what inputs/outputs are available.  At my remote station, I use a regular USB soundcard and run the Remote rig audio thru that for RTTY decoding.  For all modes, I plug my phones into the USB soundcard output, and adjust the soundcard volume control to control the audio volume of the rx signal.  I then set my audio level from the RR unit to a good one for decoding and leave it there.  The soundcard provides the variable audio I need for normal operations, and the RR unit is now putting out a constant audio signal.

Dennis W1UE

50

General discussion forum / Re: Winkey compatibility problems

« on: 2017-10-19, 14:25:45 »

Ron

I have also used a real outboard Winkey connected to a USB port of the computer, and used that to key the RR box.  I had to build a cable to attach to the RR box, but it wasn't difficult to do.  Then I had the best of both worlds- it ran quite well.

My contesting experiences using the RR Winkey have not been as bad as yours.  I've had several hours with rate >150 on CW.  You can't do that if you have many fills.  I'm also fortunate that both ends of my connection use broadband. 

FYI, where is your remote station? 

Dennis W1UE

51

General discussion forum / Re: Winkey compatibility problems

« on: 2017-10-18, 16:55:02 »

Ron, I'm going to agree with Steve N2IC.  There are Winkey emulations, and there are Winkey emulations.  RR says it offers a "Winkey Emulator", which often translates to "not a complete set of Winkey functions".  Sounds like the functions that you mentioned are not supported in this Winkey emulation.

The only thing that can be done is to add those functions to the RR Winkey Emulator.  I've been using N1MM+ and RR for several years, and while I understand why someone would want to use those functions, have never found their absence to be critical.  YMMV.

Dennis W1UE 

52

Hardware, Cabling, Installations / Re: K3 Twin - Keyer Decisions

« on: 2017-09-18, 22:54:30 »

Gary
Before the Winkey emulator was available, I had made up a custom cable to tap into that signal.  I applied the real winkey output to that line, and used the keyer in the RRC Control box to send keyed messages.  Its probably been 4 years now, but I know I had it set up to do that at one time.  Since the Winkey emulator was enabled, I'ved used that.  After a few hiccups, it has worked with a hitch.
My all time best rate on RR CW has been a 168.  I have not found latency to be a problem.

Dennis W1UE

53

Configuration of Routers, Firewalls, etc / Re: Problems with new rouer

« on: 2017-09-16, 22:16:26 »

Mitch, your last suggestion seemed to do the trick.  I had originally activated the DHCP, took the IP address assigned to the Control RRC, then made it a "non-DHCP" IP address.  I kept the IP address the same.  Based upon your last suggestion, I enabled the DHCP in the Control RRC again, and now it works.  I suspected that there might be a problem with the SIP ALG; I had attempted to turn it off in the router, per your setup sheet, but this router software doesn't allow the user to turn off SIP ALG.  I was able to verify that by a google on the router and SIP ALG.  But no mind- it seems to work now.

Thanks for the help, guys.  The magic is back.

Dennis W1UE

54

Configuration of Routers, Firewalls, etc / Problems with new rouer

« on: 2017-09-16, 11:07:40 »

I got an upgraded internet service from Verizon that included a new router.  Since then, I've been having problems connecting.  The new router is on the Control side.  I have it set for DMZ (no port forwarding); I've also tried it with Port Forwarding (but yes, not both at the same time).  No joy.
I use 12000, 11000, and 5080 as my ports.  When I try to connect by turning on the radio, I see that my SIP port out is 41042. On the status, I get a SIP ERROR "?".  When I play with the different settings in the router and Control RRC, every once in a while I get it to connect, but after a minute or so I either lose ability to key the radio using the key or I lose the audio.  Sometimes it will come back for a short time, but usually once its gone I have to turn off the Control radio and try again.

Any suggestions on where to look?  I've used the DJ0QN set up sheet, but I think the problem is not setup.

Dennis W1UE

55

Hardware, Cabling, Installations / Re: ts480 and digi modes

« on: 2017-06-17, 14:28:15 »

Bruno-
1. Plug headphones into the soundcard instead of the audio cable that you are using.  Can you now hear the digital audio signal?  If not, you have a sound card/program setup problem.
2. Since the mic works, my take is that the radio side is wired correctly.
3. I'm not familiar with the TS480- is it in Upper Sideband, or is in a Digital mode?  Sometimes, when in a digital mode, the front mike panel jack (where your audio is being input) is disconnected, and the audio must be input through a rear panel jack.  You'll need to check your manual on that.  Or, if using a digital mode, try changing it to Upper Sideband to see if it now accepts audio.

Sounds to me that you are close to getting it working!

Dennis W1UE

56

Configuration, RRC 1258 / Re: K3 Remote Radio ACC connector for RRC & SO2R-interlock simultaneously?

« on: 2017-03-22, 20:55:12 »

Gabor
I use 2 K3 radios in the exact same setup that you are using.  I have not tried it leaving the FSK pin common to both radios.  What I have experienced, when operating in the SO2R environment, that the remote connected K3 turns itself off.  We're not sure if its RFI, but several times during a contest the radio just shuts off.  The only thing that stopped it was to disconnect the RRC ACC line from the K3 when operating SO2R locally.  Since we swap the other plugs (cw, mike, ptt, key) when going from remote to local, we just added the ACC 15 to the list.

Dennis W1UE

57

Hardware, Cabling, Installations / Re: Web Access RRC ip.

« on: 2017-03-22, 20:48:22 »

Is that a typo, or did you really mean 192.168.169.1?  If so, the IP is probably incorrect.  The default is 192.168.1.169 unless you changed it.

58

General discussion forum / Re: RR-1256 K3 - Getting RRR/Q Codes out of Com1 port

« on: 2016-06-12, 12:14:13 »

Scott
We have an RRC box at the W1KM station.  To go from SO2R at the remote location to Remote at the remote location requires we change 4 cables: mike, speaker, key,   and PTT.  We have the computer connected to the Remote Rig box com port, the remote rig comport out then goes to the P3 RS232,  the P3 RS232 out goes to the K3.  None of the computer control wiring or changes in the logging program at the Remote site is necessary.

If you need more particulars on the set up let me know.  I'm not sure what you're trying to accomplish.

Dennis W1UE

59

General discussion forum / Re: Problem with N1MM+ and TS-480

« on: 2016-05-30, 14:20:05 »

Serge
This is an N1MM issue.  You have a setting wrong in the program.  Since I worked you in WPX, I can only assume you got it fixed! 
It has nothing to with Remote Rig.
Dennis W1UE

60

Configuration of Routers, Firewalls, etc / Re: Verizon FIOS with Actiontec M1424WR Router

« on: 2016-05-24, 00:58:53 »

Lee

You got it to work yet?

Dennis W1UE