Topics

16

Configuration, RRC 1258 / no responce ETH0 - Remote RRC

« on: 2013-11-26, 11:36:30 »

Hello all

I  start a new project for IC706. Take my "old" black first version .

Radio RRC - running well no problem.
Remote RRC - didnīt give response on the ethernet interface.

Readout - IP Settings - all was
255.255.255.255
IP // Subnet MAsk / Gateway and DNS !!
HTTP Port was the old - 11080


Setup via USB - RRC Manger is running without a problem.
Get and set the IPs and HTTP Port.
DHCP or static IP didnīt give a responce.

A live recording (wireshark) of the Interface traffic - didnīt show me anything :-(
After unplug 12V and put it again inside - I didnīt see anythink on the LAN interface

The amber LED is on and green LED is blinking at the interface .

I checkt different Firmware Version , at last 2.75.

Is there a way to check that it is OK ?

73 de Carsten

17

General discussion forum / Firmware Webshwitch 1216E

« on: 2013-10-31, 12:27:39 »

Hello all

I didnt found a newer firmware for my old 1216E.
Is there a newer one ?

Product Code WEB Switch 1216E
Hardware Version 1216E-2
Software Version 01.06
Web Version 01.06B
Serial number 1257

vy 73 de Carsten
DM1CG
 

18

Configuration, RRC 1258 / What is the last firmware for the silver version

« on: 2013-03-14, 18:40:55 »

Hy

I have one pair of the old silver version.
I will connect them to an AOR 5000.
In what version I will have the autoconnect function ?
Is that feature avalible for the silver version ?

best 73 de Carsten
DM1CG

19

Configuration, RRC 1258 / Profiles ?

« on: 2013-03-03, 16:28:31 »

Hello all

my RRC1258 V1 didnt save the differnet profiles.

What is the right way to save differnt settings for the Profiles.
Is it possible to change the profiles via setup manager software ?

bets 73 de Carsten
DM1CG

20

General discussion / SCR Port = DST Port

« on: 2013-02-25, 11:41:28 »

hy Guys

I tested RRC micro 1.6.4 at home and I get some timeout.
DNS IP resolve is right and OK.

RRC Micro start the SIP Communication on Port 11060 to the Source Port 11060.

For NAT the destination port and source prot have to be different - or not ?

best 73 de Carsten

21

General discussion forum / No reconnect

« on: 2013-02-24, 21:17:39 »

Hy all

I have tested the weekend much with TS-480 .

I found out, sometimes I canīt RE POWER ON the Station ,after power off.
Inside the home network all is running fine .

If i didt can re power on the Station the yellow LED da AUX / MIC is blinking.

By rest my ADSL Router / get a new IP Adresse I can re Power on the Station again.

any one know the problem

best 73 de Carsten

22

Configuration, RRC 1258 / Version 1 - set to DHCP

« on: 2011-08-21, 22:58:09 »

Hy all

Have a problem with an Version 1 .
I set it to Network settings DHCP .

DHCP didnt run at the unit .
No USB connect via Manager . I didnt want to reset - need the settings inside.
What is the way to connect an "DHCP" Unit ?

best 73 de Carsten

23

General discussion forum / RC2000 and TS2000

« on: 2010-09-30, 22:43:37 »

Hello

is here any one has running RC2000 at TS2000 ?

I have several problems - newest firmware.

73 de Carsten
DM1CG

24

General discussion forum / Lost packets - lost CMD

« on: 2010-01-26, 20:37:07 »

Hello all

i have the problem :

if i lost some audio pakets, i also lost some CMD packets.
very often my PTT at the remote station stand longer than i do it.
The display of the RC2000 some time is only half - rest comes secounds later.
or i turn the VFO - example change VHF Repeater - i hear the next channel but
the display is on the "old" QRG

In the audio stream its no problem to lost some pakets but lost pakets from the CMD
stream isnt really good.

Its very bad with 3G connection but also in the LAN .


Could it be a solution to pu the CMD streams into a TCP stream without the audio ?

 
best 73
de Carsten

25

General discussion forum / Problem - DHCP and RRC Manager

« on: 2010-01-16, 23:57:45 »

Hello all

with RRC Manager i didnt can get a connection to the control unit
if the unit do DHCP.

What is the way to config the unit ?

vy 73 de Carsten

26

General discussion forum / connection RS232

« on: 2009-12-25, 14:57:02 »

HY all

searching a solution to make a connect from my PC over RRC-1258 to my TS-2000.

MODE 4 / 9600 / 8 / 1 / N . Also connectet PIN 7 to PIN 8  at radio side

My ARPC program didnt get a connect to the TS2000.

The connection from RC2000 to TS2000 runs with no problem.

any idea

best 73 de Carsten