Messages

31

Configuration, RRC 1258 / Re: no responce ETH0 - Remote RRC

« on: 2013-11-26, 12:28:58 »

Hello Mike

If 12V isnt pluged in , I didnt get a responce on USB .

The unit wasnīt conenceted the last 6 Month .
It was not pluged to the network or power supply, it was save in an cabinet.

That is bad - never used, for what it was made :-( with a remote radio.

Carsten

32

Configuration, RRC 1258 / no responce ETH0 - Remote RRC

« on: 2013-11-26, 11:36:30 »

Hello all

I  start a new project for IC706. Take my "old" black first version .

Radio RRC - running well no problem.
Remote RRC - didnīt give response on the ethernet interface.

Readout - IP Settings - all was
255.255.255.255
IP // Subnet MAsk / Gateway and DNS !!
HTTP Port was the old - 11080


Setup via USB - RRC Manger is running without a problem.
Get and set the IPs and HTTP Port.
DHCP or static IP didnīt give a responce.

A live recording (wireshark) of the Interface traffic - didnīt show me anything :-(
After unplug 12V and put it again inside - I didnīt see anythink on the LAN interface

The amber LED is on and green LED is blinking at the interface .

I checkt different Firmware Version , at last 2.75.

Is there a way to check that it is OK ?

73 de Carsten

33

General discussion forum / Re: Firmware Webshwitch 1216E

« on: 2013-11-12, 12:33:53 »

Hello Mike

Yes we have. Sometimes I cannot controll the webswitch.
I am logged in , but I can not do anything.

In that case I have to take another Browser
- relogin - and all is OK. But not all user have more then one browser.
We have the problems with IE9 and Iron.

73 de Carsten
DM1CG

34

General discussion forum / Firmware Webshwitch 1216E

« on: 2013-10-31, 12:27:39 »

Hello all

I didnt found a newer firmware for my old 1216E.
Is there a newer one ?

Product Code WEB Switch 1216E
Hardware Version 1216E-2
Software Version 01.06
Web Version 01.06B
Serial number 1257

vy 73 de Carsten
DM1CG
 

35

Configuration, RRC 1258 / Re: What is the last firmware for the silver version

« on: 2013-03-18, 09:43:39 »

Hello Mike

It tested again but both Units are "now" Radio type.
I have no more the settimg from the conroler to make a connect from one unit to the other .

How a can made the controller unit again to a controller unit ?

best 73 de Carsten

36

Configuration, RRC 1258 / Re: What is the last firmware for the silver version

« on: 2013-03-15, 10:25:19 »

Hello Mike

great !

I will check it.

-- setting gone to do a connect from "Control to Radio
-- I have now two units called Radio ....
-- SN 1628 & 1629
-- MAC 00:50:c2:11:8e:2c & 00:50:c2:11:8e:2d


vy 73 de Carsten
DM1CG

37

Configuration, RRC 1258 / What is the last firmware for the silver version

« on: 2013-03-14, 18:40:55 »

Hy

I have one pair of the old silver version.
I will connect them to an AOR 5000.
In what version I will have the autoconnect function ?
Is that feature avalible for the silver version ?

best 73 de Carsten
DM1CG

38

General discussion forum / Re: No reconnect

« on: 2013-03-04, 13:52:38 »

Yesterday at Remote side I get the same Error.

I was inside the same IP network !
I made one connect - working some W Station on 10m.
Power off the station... repower -> SIP ERROR.

I give the control unit another IP , but same SIP ERROR.

Disconencted the power supply at the radio side and i can connect again.
One Time -> SIP Error

?
Best 73 de Carsten

39

Configuration, RRC 1258 / Re: Profiles ?

« on: 2013-03-04, 13:46:07 »

Thanks both

:-) running now.

40

Configuration, RRC 1258 / Profiles ?

« on: 2013-03-03, 16:28:31 »

Hello all

my RRC1258 V1 didnt save the differnet profiles.

What is the right way to save differnt settings for the Profiles.
Is it possible to change the profiles via setup manager software ?

bets 73 de Carsten
DM1CG

41

General discussion forum / Re: No reconnect

« on: 2013-02-25, 14:26:05 »

Hy Guys

I tested more and I get again it.
I take an other UNIT RRC 1258 - client side - FW 2.68
Make the setup like my Control Unit

Over the WEB interface I make 10 -15 Connect - Disconnects with a break around 10sec.

Now a got no connects more. I produced an SIP Error. I am not able to do an conenct again.
Now I have to swap my public IP adresse .. on that place I have a fix one. :-(


Name   Value
Control panel   OFF
Radio   OFF
Connection status   Disconnected
SIP status   Unknown(1)
Last SIP error   SIP Error
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   4
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
SIP Out port   11060
SIP In port   11060
Audio Out port   11050
Audio In port   11050
Command Out port   11040
Command In port   11040
External SIP In port   11060
External Audio In port   11050
External Cmd In port   11040
Other party   IP ADRESSE
Input 0   High
Input 1   High
Input 2   High
Output 0   High
Output 1   Low
Output 2   Low
DNS status   OK,
Active profile:   DM1CG
PTT status:   OF

42

General discussion / Re: SCR Port = DST Port

« on: 2013-02-25, 13:06:17 »

Hello Mitch

If that is right , I never have a change to be QRV from a hotel or so where I havent access to the NAT Route - to forwarding the ports. NAT is only possible if SCR und DST port are different.


In my understanding TCP/IP do :
MY PC SCR Port xxxx - > MY station IP Port 11060
My station answer on Port 11060 -> my PC Port xxxx

Then NAT is possible.

If Scr Port and Dst Port are the same - NAT is normally not possible

My WEB interface is on 12380 at RRC Unit side.

If i start the browser an sniff the network traffic I saw :
my browser open PORT 50889 -> WEB Interface RRC 12380
Webinterface 12380 -> my browser 50889

Best 73 de Carsten


 
 

43

General discussion / SCR Port = DST Port

« on: 2013-02-25, 11:41:28 »

hy Guys

I tested RRC micro 1.6.4 at home and I get some timeout.
DNS IP resolve is right and OK.

RRC Micro start the SIP Communication on Port 11060 to the Source Port 11060.

For NAT the destination port and source prot have to be different - or not ?

best 73 de Carsten

44

General discussion / Re: RRC Client Errors

« on: 2013-02-25, 10:02:52 »

Hello Roland

For my understanding COM0 is only for the Control Panel and not for using the Kenwood program.
So I have to use for control program COM1 . At RRC Unit I have a RS232 cable from COM1 to RS232 for TS-480.

The RRC Micro Client give my only one COM Port for choose . In my case COM6.

best 73 de Carsten

45

General discussion forum / No reconnect

« on: 2013-02-24, 21:17:39 »

Hy all

I have tested the weekend much with TS-480 .

I found out, sometimes I canīt RE POWER ON the Station ,after power off.
Inside the home network all is running fine .

If i didt can re power on the Station the yellow LED da AUX / MIC is blinking.

By rest my ADSL Router / get a new IP Adresse I can re Power on the Station again.

any one know the problem

best 73 de Carsten