Messages

2551

General discussion forum / Re: ICOM CI-V and HRD not working

« on: 2011-09-15, 21:11:24 »

There is no connection between the serialport settings and the mic signal or mic settings, they are totally independent. So keep the setting where the CI-V works and check that you have not changed the codec input gain in the control-RRC by misstake.
/mike

2552

General discussion forum / Re: Setting up RemoteRig with TS-480 - I'm missing something!

« on: 2011-09-14, 07:32:53 »

Hi

It doesn't matter how the local networks are numbered. I understand you can browse the remote unit over the internet. That's good then most settings are correct. Check that you have changed the "SIP contact" in the Control-RRC after testing on local LAN, now you should enter the dyndns address or the public IP of the remote router in the "SIP contact" field. If you have it correct and it's still not connect, probably the ISP has reserved port 5060 for their own IP-telephony, try to change the SIP port in both ends to something else 5061 for example.

73 de mike

2553

General discussion forum / Help with Remote control of a Yeasu rotator via GS-232B needed.

« on: 2011-09-13, 11:05:50 »

We have a customer who has problem to get remote control of a Yaesu G-5500 rotator with a GS-232B interface to work via the RRC-1258MkII. Is there anybody out there using that combination, who can help with settings and cabling. We do not have one at Microbit that we can test with.

73 de Mike

2554

General discussion forum / Re: TS-480 No SSB Transmit

« on: 2011-09-13, 07:24:04 »

Hi
Typically a red jumper problem, First check the placement and then check them with an ohm meter.

/mike

2555

Allmänt diskussionsforum / Re: Problem med att starta IC-706MKII

« on: 2011-09-02, 08:39:45 »

Det behövs inga inställningar i routern på kontrollsidan. Kolla alltid att routern är uppdaterad med senaste programvaran, särkskilt d-link har skickat ut många burkar med tveksam programvara, men det brukar fixa sig när man uppdaterar till deras senaste program. Idag är Time to market viktigare än att det man skickar ut skall fungera.

73de mikael

2556

General discussion forum / Re: TS-480 + RRC without Head?

« on: 2011-08-31, 16:37:21 »

No workaround needed. TS-480 do not need the control head. But both the TTL control cable and the CAT cable must be used from RRC o Radio and the settings must be OK. HRD starts the radio.

73 de mike

2557

Allmänt diskussionsforum / Re: Microbit Setup Manager

« on: 2011-08-28, 11:14:26 »

Nej det går inte och man skall absolut inte lämna i USB kabeln i Radio-RRC, den för ut störningar från PC.n och riskerar att plocka upp HF.
Jag har själv kört remote i tre vintrar med både RRC och webswitchar och har aldrig haft anledning att behöva ansluta en usb till någon av dem.

/mikael

2558

General discussion / Re: PC Client with Yaesu Twin

« on: 2011-08-22, 22:22:39 »

Hi

Have you changed to COM0 for the CAT connection in the RRC-client ? As far as I rembember com0 should be used for Yaesu twin as the Radio-RRC is set so Com2 is in parallell with com0, the commands is then going via com0

73 de mike

2559

General discussion forum / Re: TM-D710 AUX/MIC jumper settings - error in manual?

« on: 2011-08-18, 15:33:03 »

Thank you for the info It will be changed in the Manual version A16.

73 de mike

2560

General discussion forum / Re: FTdx9000MP to FTdx9000MP Twin RRC's

« on: 2011-08-18, 15:28:08 »

The 9000 to 9000 issue is now fixed thanks to OH2BH Martti who brought two 9000:s to us.

73 de mike

2561

General discussion forum / Re: Kenwood TM-D700 Works Great with RemoteRig

« on: 2011-08-18, 15:24:41 »

Ok thank you for testing. I will add the D700 to the list of supported radios.

73 de mike

2562

General discussion forum / Re: Earlier Kenwood radios - what works?

« on: 2011-08-18, 15:22:10 »

Hi if you change to mode 3 it may work. In mode 4 the messages need to end with a ; to be sent. Maybe it's not the same protocol for the old ones.

73 de mike

2563

General discussion forum / Re: YaesuTwin: audio level main receiver

« on: 2011-08-18, 15:19:56 »

There is still only one audio amplifier even in the Dual RX version. So if two speakers are used they must be of a active type with built in amplifiers. For example PC-speakers. With the jumper you can change the ordinary audio channel to be the same level as the extra channel eg. headphone levels.

73 de mike

2564

General discussion forum / Re: YaesuTwin: no power output when using split

« on: 2011-08-18, 15:10:30 »

Hi Mitch
As you already know we do not do change the control messages sent from the control radio to the remote radio. I can't see that there is anything we can do about it, it must be an bug inside the radio itself.

73 de mike

2565

General discussion forum / Re: RRC-MICRO, TS-480, HRD, DM780

« on: 2011-08-18, 10:48:44 »

Hi

As the RRC-PC-Client only sends the data from HRD, to and from the radio without looking into the messages this will not work.
The PTT commands are sent to the radio but the PC-client will not shift to TX so the audio comes through. I know lot of people using Remoterig for PSK but they probably have the boxes and use a ptt input via USB or serialport.

73 de mike