2566
General discussion forum / Re: RCC-1258 'S LED INDICATORS
« on: 2011-08-17, 19:17:24 »
The LEDs are described in the downloadable users manual
73 de mike
73 de mike
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2567
General discussion forum / Re: CW Keying issue
« on: 2011-08-17, 19:16:26 »
When using CW packet loss is not acceptable, it will be errors if a CW packet is lost. Jitter is acceptable as long as it's within the "key delay" settings. Set "key delay" well over the longest ping time, try 150 ms in this case.
73 de mike
73 de mike
2568
General discussion / Re: Which version of RRC-1258 is needed ?
« on: 2011-08-06, 22:59:09 »
yes it is, with the limitation that the RRC version 1 do not have COM2
73 de mike
73 de mike
2569
General discussion / Re: IC Socket Orientation
« on: 2011-08-06, 22:57:48 »
pin 1 is at the position shown in manual, no matter how the socket looks like or is mounted.
73 de mike
73 de mike
2570
General discussion / Re: TS-480 Setup
« on: 2011-07-23, 09:10:24 »
The TS-480 control panel do not use the standard Kenwood CAT protocol to communicate with the Radio it's a different protocol which is not public, and there is no documentation available for it. The RRC boxes just setup a channel for it we do not bother whats inside.
The same is for the RRC-Micro we just set up a channel for the HRD or other PC software to use for the CAT protocol.
There is no chance for a patch as you say, to convert between these protocol. But there are lot of other products giving you extra serial ports for example from Tibbo. Of course you can return the RRC-Micro if you can not use it.
73 de mike
The same is for the RRC-Micro we just set up a channel for the HRD or other PC software to use for the CAT protocol.
There is no chance for a patch as you say, to convert between these protocol. But there are lot of other products giving you extra serial ports for example from Tibbo. Of course you can return the RRC-Micro if you can not use it.
73 de mike
2571
General discussion / Re: TS-480 Setup
« on: 2011-07-22, 17:21:23 »
but you must connect cable between Radio-RRC COM2 and the radio CAT port.
and in the RRC-micro you set up COM 2 to mode 4 and select one of the virtual comport.
then in the HRD you select the same virtual comport
73 de mike
and in the RRC-micro you set up COM 2 to mode 4 and select one of the virtual comport.
then in the HRD you select the same virtual comport
73 de mike
2572
General discussion / Re: Com ports being used
« on: 2011-07-22, 10:21:17 »
You can reassign the comport numbers in Windows like for all other comports
73 de mike
73 de mike
2573
General discussion / Re: TS-480 Setup
« on: 2011-07-22, 10:19:36 »
Hi
most people who have this problem have forgot that when they try to control the TS-480 using HRD or other PC software, a CAT cable must be connected between COM2 and the radio CAT-port. HRD etc can't use the same control channel as the front panel. When using TS-480 via the CAT port, it should be seen as any other Kenwood radio. From your limited descriptions I can't say anything else.
73 de mike
most people who have this problem have forgot that when they try to control the TS-480 using HRD or other PC software, a CAT cable must be connected between COM2 and the radio CAT-port. HRD etc can't use the same control channel as the front panel. When using TS-480 via the CAT port, it should be seen as any other Kenwood radio. From your limited descriptions I can't say anything else.
73 de mike
2574
General discussion forum / Re: TS 480 proplem with local setup
« on: 2011-07-20, 10:00:12 »
If you are testing on local LAN and the yellow led flash the you have not set the correct ip in the "sip contact" box. The sip contact is like the phone number to the Radio-RRC.
73 de mike
73 de mike
2575
Hardware, Cabling, Installations / Re: I/O connector in RRC-1258 ver 1
« on: 2011-07-12, 23:47:04 »
The Links are fixed, Im sorry for the trouble
73 de mike
73 de mike
2576
General discussion forum / Re: Remoterig PTT problem /Kenwood wiring
« on: 2011-06-25, 11:18:23 »
The only thing which can activate PTT is that the input is grounded. It cant be anything wrong with the hardware. Check that he have turned the box the right way when identifying pin 1, that's the most common problem. We do not send out used units and I hope our distributors do not either. But of course we can have missed put the bag with the red straps into the box, give me the address and I will send the missing straps.
73 de mike
73 de mike
2577
Allmänt diskussionsforum / Re: 1216L Rotator controller A/D problem ?
« on: 2011-06-22, 23:38:17 »
Hej
Du har rätt jag mindes fel, blandade ihop den med nått annat. Vi skall titta på om vi kan göra nått valbart.
73 de mikael
Du har rätt jag mindes fel, blandade ihop den med nått annat. Vi skall titta på om vi kan göra nått valbart.
73 de mikael
2578
Configuration of Routers, Firewalls, etc / Re: what am i doing wrong ?
« on: 2011-06-22, 23:33:32 »
Hi
There are lot of bad routers out there in which DMZ and and portforwarding are not working properly, but after udating them with latest firmware, the problems are solved in most cases. Also check if there is something called SIP ALG it should NOT be activated. Send me exported settings and login info so I can test from here.
/mike
There are lot of bad routers out there in which DMZ and and portforwarding are not working properly, but after udating them with latest firmware, the problems are solved in most cases. Also check if there is something called SIP ALG it should NOT be activated. Send me exported settings and login info so I can test from here.
/mike
2579
Configuration of Routers, Firewalls, etc / Re: what am i doing wrong ?
« on: 2011-06-21, 13:38:27 »
Hi
you have mixed up udp and tcp in the portforwarding config.
SIP,control, and audio should be UDP and webserver TCP
73 de mike
you have mixed up udp and tcp in the portforwarding config.
SIP,control, and audio should be UDP and webserver TCP
73 de mike
2580
Allmänt diskussionsforum / Re: 1216L Rotator controller A/D problem ?
« on: 2011-06-20, 23:23:34 »
Hej
det går inte att ändra med mjukvara, A/D omvandlaren har 10 bitars upplösning från 0-5V och ingången är tänkt för 0-15V. Men om du byglar över 220K motståndet som sitter direkt på ingången så får du 0-5V ingångs område istället. Då får du ju lite bättre upplösning.
73 de mikael
det går inte att ändra med mjukvara, A/D omvandlaren har 10 bitars upplösning från 0-5V och ingången är tänkt för 0-15V. Men om du byglar över 220K motståndet som sitter direkt på ingången så får du 0-5V ingångs område istället. Då får du ju lite bättre upplösning.
73 de mikael