91
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
92
Konfiguration av RRC 1258 / Re: IP setup problem
« on: 2023-07-18, 20:08:22 »
Hi
if you use a ddns serives at the radio site you should enter the ddns own hostname as "SIP contact" in the Control-RRC radio setup, no IP address.
You have setup portforwarding in the new router and checked that you have a public IP ?
http://www.remoterig.com/wp/?page_id=3494
73 de mike
if you use a ddns serives at the radio site you should enter the ddns own hostname as "SIP contact" in the Control-RRC radio setup, no IP address.
You have setup portforwarding in the new router and checked that you have a public IP ?
http://www.remoterig.com/wp/?page_id=3494
73 de mike
93
General discussion forum / Re: Rising 3-tone signal when attempting to connect to remote station
« on: 2023-07-10, 07:22:08 »
Hi
Check what the status page says in your Control-RRC. If the Radio side is reachable for others the problem is at your side. If the radio side has a static IP you probably have set the static IP as SIP contact ? and then you are not depending on a working DNS or DDNS hostname, If you use a Remoterig DDNS hostname as Sip contact it can be that the Radio-RRC has not updated the DDNS system after the database was cleared about two month ago. You can check if the ddns hostname is updated here http://ddns.remoterig.com/status/
73 de mike
Check what the status page says in your Control-RRC. If the Radio side is reachable for others the problem is at your side. If the radio side has a static IP you probably have set the static IP as SIP contact ? and then you are not depending on a working DNS or DDNS hostname, If you use a Remoterig DDNS hostname as Sip contact it can be that the Radio-RRC has not updated the DDNS system after the database was cleared about two month ago. You can check if the ddns hostname is updated here http://ddns.remoterig.com/status/
73 de mike
94
Konfiguration av RRC 1258 / Re: no contact with mine RRC-1258 (radio version)
« on: 2023-06-26, 07:36:23 »
Hi
what is show when you do find "find devices" ?
mike
what is show when you do find "find devices" ?
mike
95
General discussion forum / Re: rfi with amp
« on: 2023-06-11, 17:26:56 »
Hi
RFI is in most cases caused by bad balanced antennas. My experience is that it's no idea to try to put ferrit etc on the cables inside the chack, you have to keep the RF at the antenna. Best is to change antenna the second best is to put RF chokes on the antenna feeders as near the antenna as possible. If the antenna is extremly near the shack it might be RF direct from the antenna but thats not as common as the RFI coming with the feeder back to the shack
There so many things which can pick up RF. like Modems, routers, ethernet switches, ethernet cables and the audio cables connected to the RRC. DC -cables etc
As you say it disconnects sometime I guess it's on the ethernet side the problem is. The cables it self, or a plastic switch or router etc
Also try with separate Power supplies for the Radio and the RRC if you do not already have that, to avoid ground loops
73 de mike
RFI is in most cases caused by bad balanced antennas. My experience is that it's no idea to try to put ferrit etc on the cables inside the chack, you have to keep the RF at the antenna. Best is to change antenna the second best is to put RF chokes on the antenna feeders as near the antenna as possible. If the antenna is extremly near the shack it might be RF direct from the antenna but thats not as common as the RFI coming with the feeder back to the shack
There so many things which can pick up RF. like Modems, routers, ethernet switches, ethernet cables and the audio cables connected to the RRC. DC -cables etc
As you say it disconnects sometime I guess it's on the ethernet side the problem is. The cables it self, or a plastic switch or router etc
Also try with separate Power supplies for the Radio and the RRC if you do not already have that, to avoid ground loops
73 de mike
96
Feature Requests / Re: hoping that Nano will work on Yaesu FT7800
« on: 2023-06-09, 15:37:01 »
Hi
FT-7800 has no CAT interface so it will never work with a external control device
73 de mike
FT-7800 has no CAT interface so it will never work with a external control device
73 de mike
97
General discussion forum / Re: AS-1289 Automatic switching via ICOM 7100
« on: 2023-06-06, 18:34:07 »
Det går ju, ställ in lämplig disconnect timout så slår alla reläer av x miuter efter sista CAT commando
/micke
/micke
98
General discussion forum / Re: AS-1289 Automatic switching via ICOM 7100
« on: 2023-05-30, 15:45:44 »
hej
det är många ställen det skall vara rätt, se till att baudrate är samma tex 9600 i AS-1289, RRC com2, och IC-7100 ( den skall inte stå i auto).
Se till att protocol är rätt på com2, ICOM-CIV
ip addresser och portnummer matchar
CI-V adress matchar osv
när dom grejerna är rätt då skall radions frekvens synas på AS-1289 websidan, sedan återstår att sätta upp vilken antenn som skall användas för resp frekvens
vet inte hur långt du kommit
/micke
det är många ställen det skall vara rätt, se till att baudrate är samma tex 9600 i AS-1289, RRC com2, och IC-7100 ( den skall inte stå i auto).
Se till att protocol är rätt på com2, ICOM-CIV
ip addresser och portnummer matchar
CI-V adress matchar osv
när dom grejerna är rätt då skall radions frekvens synas på AS-1289 websidan, sedan återstår att sätta upp vilken antenn som skall användas för resp frekvens
vet inte hur långt du kommit
/micke
99
Konfiguration av RRC 1258 / Re: xiegu G90 with remoterig?
« on: 2023-05-28, 16:39:07 »
Hi
on page in the Xiego manual they write about CAT
Basic SETUP G90 CAT Control for Windows HAM Software General information about CAT CAT is an abbreviation for Computer Aided Transceiver and describes the way to operate your rig via a serial protocol in sync with your PC. There are numerous ways to connect your rig to the PC e.g. via RS232, via ACC port or via USB, but in all cases you have to emulate the serial connection for the protocol, which is used by the vendor. Xiegu uses the protocol spec from ICOM, also known as CI-V (Computer Inferface Five). The complete spec of ICOMs CI-V can be found when you google it, e.g. here: http://www.plicht.de/ekki/civ/civ-p0a.html To control the XIEGU rigs you can use the IC-7000 or IC-718 as the device in different ham radio software. Which one works best depends on the implemented software design, the following screen shots are best practice and work in general. Xiegu only has implemented a subset of the functionality of the CI-V protocol, but this is actually not documented. So the only method is trial and error along with other Ham operators knowledge
https://www.connectsystems.com/products/top/radios/G90/G-90-Manual.pdf
it looks like they use a subset of ICOM CI-V so if you set Remoterig to program mode 1 ICOM CI-V it may work if you make a proper cable, it looks like it's not the same as ICOM CI-V cable
73 de mike
on page in the Xiego manual they write about CAT
Basic SETUP G90 CAT Control for Windows HAM Software General information about CAT CAT is an abbreviation for Computer Aided Transceiver and describes the way to operate your rig via a serial protocol in sync with your PC. There are numerous ways to connect your rig to the PC e.g. via RS232, via ACC port or via USB, but in all cases you have to emulate the serial connection for the protocol, which is used by the vendor. Xiegu uses the protocol spec from ICOM, also known as CI-V (Computer Inferface Five). The complete spec of ICOMs CI-V can be found when you google it, e.g. here: http://www.plicht.de/ekki/civ/civ-p0a.html To control the XIEGU rigs you can use the IC-7000 or IC-718 as the device in different ham radio software. Which one works best depends on the implemented software design, the following screen shots are best practice and work in general. Xiegu only has implemented a subset of the functionality of the CI-V protocol, but this is actually not documented. So the only method is trial and error along with other Ham operators knowledge
https://www.connectsystems.com/products/top/radios/G90/G-90-Manual.pdf
it looks like they use a subset of ICOM CI-V so if you set Remoterig to program mode 1 ICOM CI-V it may work if you make a proper cable, it looks like it's not the same as ICOM CI-V cable
73 de mike
100
Configuration of Routers, Firewalls, etc / Re: problem detection iphone / microbit manager
« on: 2023-05-26, 20:30:51 »
set DHCP = yes in the RRC as you probably have a different LAN from the phone
73 de mike
73 de mike
101
Configuration of Routers, Firewalls, etc / Re: problem detection iphone / microbit manager
« on: 2023-05-26, 17:30:32 »
Hi
probably the Iphone is set to share wifi on 5GHz you have to change to 2.4 GHz
73 de mike
probably the Iphone is set to share wifi on 5GHz you have to change to 2.4 GHz
73 de mike
102
General discussion forum / Re: RRC-1258MkIIs
« on: 2023-05-26, 12:49:23 »
Remoterig is shipped to the distributors today, so next week they will have them in stock
73 de mike
73 de mike
103
General discussion forum / Re: Product
« on: 2023-05-26, 12:31:10 »
Yes today most orders are shipped
Mike
Mike
104
Configuration of Routers, Firewalls, etc / Re: 25.05.2023. unable to connect
« on: 2023-05-25, 12:08:44 »
There has been a problem at the server hotel during the night causing problem with the DDNS but it's working now
and remember the info about the DDNS system
Note! We do our best to maintance the ddns system for 24/7 availability but as it is a free service we do not give any guaranties. Do not expect anything to happen outside office hours, and there is no need to ask by phone, forum or email when it will be fixed, we always do our best to fix it. If you need 100% availability you may use one of the commercial ddns services.
73 de mike
and remember the info about the DDNS system
Note! We do our best to maintance the ddns system for 24/7 availability but as it is a free service we do not give any guaranties. Do not expect anything to happen outside office hours, and there is no need to ask by phone, forum or email when it will be fixed, we always do our best to fix it. If you need 100% availability you may use one of the commercial ddns services.
73 de mike
105
General discussion / Re: 1.11.0 How to install
« on: 2023-05-23, 11:06:01 »
Hi
No you do not have to uninstall first, it's handled automatically
73 de mike
No you do not have to uninstall first, it's handled automatically
73 de mike