Messages

16

Configuration of Routers, Firewalls, etc / Re: Can't Connect Remotely from a site

« on: 2015-11-28, 21:40:33 »

I have had the SIP ALG disabled. I think I had placed my laptop on  the DMZ (wireless port sharing).
My ports are in the 13000 range....
 
OK, now I have a bit of egg on my face!!

Looks the newest version of Symantec EndPoint AV is causing the issue from here!!!  Wish I had figured it out sooner. Not sure why the update is causing the problem. It was working when I tested from work on Monday or Tuesday.

More to learn!! Thanks for pointing me in the right direction!!

Will WC2L

17

Configuration of Routers, Firewalls, etc / Re: Can't Connect Remotely from a site

« on: 2015-11-28, 20:15:13 »

I would say more of the second...
I had not tried from this QTH before Thursday night... This weekend was the first. Friday I spent more time testing.

SO from work, other traveling and etc. the remote stuff has worked just fine. Myself and others were able to connect. I am not able to connect from where I am this weekend. I have tested with my DNS name and the public IP address from the Control side. I have triple checked the SIP settings. I have even placed them side by side to compare.

I know that my DNS and IP is working, I have tested this by using HTML, telnet, and a couple of other tests. If I see your reply and I am here, I will test. I would like to know what else I need to do.

I of course have restarted both RRC units and both routers.
TNX Will

18

Configuration of Routers, Firewalls, etc / Can't Connect Remotely from a site

« on: 2015-11-28, 02:07:11 »

I have been playing around with remote operation of my station. I have even had a person operate my station from Europe. I can even connect from my office and control my station...

In getting ready for CQWW, I tried to connect to my station while I am away for Thanksgiving. I can web to it the Radio RRC, I can remote to the PC, heck I can telnet to my dx cluster node. When I try to connect from my control RRC, I get a SIP status: Unknown(1) and Last SIP error: SIP Error

I have even tried looking at ports and things, no joy and happiness. The router here is a Netgear WNR3500L. It does have the latest firmware, I can't seem to see connect. I know it is close to CQ WW, but lets see if I can get this work!!

TNX Will WC2L

19

Hardware, Cabling, Installations / Re: No Audo - Cable/jumper Settings

« on: 2015-07-04, 19:37:59 »

Then I have it right. I am going by page 22 of the manual.
The notch is the side that shows Pin 1 on top,.
The picture shows the RJ-45 below the socket
I had the pin number wrong for the lower side.
They must be using the RJ-45 numbers
4 - 6
5 - 5
7 - 7
8 - 4
I have UTP set for continuous.
Will have to trace it out to see if it has continuity.

Will WC2L

20

Hardware, Cabling, Installations / Re: No Audo - Cable/jumper Settings

« on: 2015-07-04, 18:58:10 »

Hi Mitch,
I am guessing you are talking the about the  RJ-45.

Will WC2L

21

Hardware, Cabling, Installations / No Audo - Cable/jumper Settings

« on: 2015-07-04, 15:31:41 »

I am a bit perplexed. I have gotten most things to work. Radio communications, RX audio and CW, but the SSB audio is not working. I have looked at this a few times. I am using the RRC-1258MkIIs with the FTdx5000 on the radio side. I am using just a computer on the control side.

I followed the pictures for the jumpers and they look like they follow the same path as the boards pictured in the manual, The cables I made for the AUX/MIC inputs were made from CAT 5/6 wiring. I was looking at the generic or 2000 pattern. I only hooked up 5-8 (PTT & MIC).

When I am looking at the jumper configuration. The front of the unit is facing me. So Pin 1 is all the way to the right and Pin 8 is to the left on the socket. Since there are only four jumpers, I am guessing that these are the only pins used.
Here is my Jumper Settings:
Back to Front
4 - 5
5 - 8
7 - 7
8 - 4

If I am reading the cable wiring right:
CAT Wiring Side - Radio Side
1 - Orange Stripe
2 -  Orange
3 - Green Stripe
4 - Blue - Pin 7
5 - Blue Stripe - Pin 8
6 - Green - Pin 6
7 - Brown Stripe - Pin 6
8 - Brown
The tab is on the top side (like shown in the pictures).
Do I need the rest? All Do I really care about any of the other connections?
Does VOX work remotely?

TNX Will WC2L

22

Configuration, RRC 1258 / Re: FTdx5000 Help

« on: 2015-06-23, 20:25:29 »

no error, just no radio status on either side:
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(44)


Will WC2L

23

Configuration, RRC 1258 / Re: FTdx5000 Help

« on: 2015-06-23, 19:01:11 »

I don' think it is a network issue. I can hear audio on the control side. I did mention that I have connectivity from the control to the radio side. I am local to everything (radio, computer, both units).  I will send you the info.

Will WC2L

24

Configuration, RRC 1258 / FTdx5000 Help

« on: 2015-06-23, 17:55:16 »

I have been looking at the manual and trying to setup RRC-1258 MkII: Control and RRC-1258 MkII: Radio. I have the latest firmware. The two devices are talking in the status window. I have the radio connected to Com2 and I have the computer connected to the control on Com2.

I have straight through cables built with pins 2,3,5,7 & 8 connected (on both devices). On the RRC-1258 MkII: Radio  I am not seeing the radio connect. The radio is set for 38400 and RTS is disabled.

I am not sure what I am missing. Can someone help? Give me pointers??
Eventually it would be nice to hook up the Navigator and have it all work.

TNX Will WC2L

25

General discussion forum / Re: Dayton RemoteRig Questions

« on: 2015-05-07, 01:36:46 »

Hope to meet you at Dayton!!

Will WC2L