Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dl2nd

Pages: 1 2 [3] 4
31
General / Some Problems
« on: 2015-01-05, 12:49:54 »
Hello,

I am using a Galaxy Note 3 with Android 4.4.2, the RRC-1258 Firmware Version is 2.83.
My radio is a Kenwood TS-2000.

When the connection is established and I enter the frequency, for example 14305 Mc or a higher Band, the “Mode” changes to LSB.
It is impossible to change to USB with the “Mode” button, only AM and LSB are possible.
On 40m Band it works ok and the “Mode” changes to LSB.

When I switch the Band with “Band”, the Mode is already selected.

Another problem. The frequency is not displayed in both cases.

Regards,

Uwe


32
General / Re: Frequency refresh
« on: 2014-10-30, 22:22:01 »
Hi Marco,

I have exactly the same Problem.
I am using a Samsung Galaxy Note 3 and Android 4.4.2.

73,
Uwe


33
General discussion forum / Rotator Create RC5B-4-P and 1216H ?
« on: 2014-10-27, 21:43:27 »
Does anybody know, if the Create RC5B-4-P is working properly with the webswitch ?

Thank you for any answers.
Uwe


34
General discussion / Re: Error in XML Document
« on: 2014-08-25, 06:44:02 »
Thank you Roland,

it works.

Uwe

35
General discussion / Error in XML Document
« on: 2014-08-22, 12:48:31 »
Hello,

my Client works fine since a few months.
Today I got the attached error message.
Does someone know what it means ?
A reboot does not help.
My OS is Windows XP 32Bit

Thank you.
Uwe



36
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-16, 19:08:30 »
Sorry for the delay.

The TS-2000 has a Problem with the serial.
I have borrowed a TS-2000 from a good fried and everything is ok right now.

Thanks @all for the help.

Uwe

37
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-05, 09:50:01 »
Okay Jan,

thank you very much.

I will check it when I am at home at the weekend.
The best test is to connect a computer (serial port) with the radio directly.

Uwe

 

38
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-05, 07:06:13 »
After a short night I have new results now:

During while Ham Radio Deluxe trying connect to the virtual COM, the "UDP status cmd" shows
OK (40). After that, a countdown starts and count down ... OK (39) ... OK(38) .... and than Error (0).
I dont know if that is a normal reaction ?

Still have the problem HRD cannot connect (got frequency reading error) to the virtual COM.

Uwe

39
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-04, 16:42:24 »
Ok, sent to: mikael(at)styrefors.se

The radio is off at the moment but I can switch it on, if you want (remote).


40
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-04, 15:45:44 »
Yes, for sure.
I am using the same ports with the combination RRC (Remote) - RRC (Radio) and it works.
Port forwarding settings: UDP -> 13000 - 13002 for 192.168.1.228 (RRC Radio)

If you like to try it I can send you the RRC radio url via private mail.

Uwe





41
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-04, 14:47:46 »
Yes

42
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-03, 08:10:06 »
Hello @ALL,

I have new results, looks better but not hundred percent.
With Mitchs help I am a step forward now  :)

COM0 and COM2 (RRC) connected to TS-2000.
- PTT works
- RX works
- TX works, I think

The debug file looks better but still with error "401 unauthorized".
The communications between COM2 and HRD fails.
The RRC Hompage still shows "connection faulty".

@Jan
Maybe, the debug file could help you ?

Uwe





43
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-02, 19:42:36 »
Okay,

Mitch told me, I have to use RRC-COM2 instead off RRC-COM0 with Kenwood TS-2000.
I will try it ...

Uwe

44
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2013-06-02, 11:38:34 »
Okay, thanks.
To exclude a problem with my router configuration, I have tried the connection in my own network (without the router)
but got the same error.
In matching with the ports at the 1258 status homepage, I think I have the correct settings in the RRC Client:
SIP Port: 13000
Command Port: 13002
Audio Port: 13001

Should be ok ?
By the way, when I disconnect the connection, the radio (TS-2000) switched off.

What strikes me, the outgoing ports of the RRC-1258 are allways different (not the command port, it is zero) which each new connection. I that correct ?

I took a look with wireshark and there are following records in the capture file; answer from RRC-1258:
Status: 401 unauthorized
Status: 403 forbidden

Uwe

45
General discussion / Connected to sip - but Connection status Faulty ?
« on: 2013-06-01, 17:47:10 »
Hello,

the connection between two RRC-1258 works.

I have a problem with the connection between the PC Client and the RRC-1258.

The RRC Client shows: Connected to sip: ...... and the RTP lights green but the RRC-1258 Radio Status Homepage shows:

Radio   ON
Connection status   Faulty(See below)
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   Error(0)
SIP command timeout   0
Rx Jitter buffer size   7
Rx Jitter delay   5
Dual Rx   0
Current audio packet size   40
Current audio quality   0 - alaw 8 kHz
SIP Out port   61389
SIP In port   13000
Audio Out port   61392
Audio In port   13001
Command Out port   0
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   79.252.241.174
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status   Unknown
Ping status (watchdog)   Off
DNS status   OK, remoterig.com = 193.202.110.185
Active profile:   Default
PTT status:   OFF
Antenna-Switch (IP)   not connected

The router ports (NAT) should be ok, I have tried the connect also in my own network but I got the same problem.
I have made 2 Files in the debug mode: external connection and connection in my own network.
In both files there are a entry with ...unauthorized ...., I have double checked my sip password, should be ok.

Thank you for your help.

Uwe

Pages: 1 2 [3] 4