Messages

1

General discussion forum / Re: TS-590S Twin setup: No memory channels or split operation

« on: 2023-11-15, 21:10:57 »

Hi Christian,

nice to hear, you solved the problem. So also you told me via email.
Enjoy remoting and gd dx with splitoperation, hi.

73
Willi

2

General discussion forum / Re: TS-590S Twin setup: No memory channels or split operation

« on: 2023-11-12, 09:26:02 »

Split operation with TS-590S is working very well at me.

73
Willi
DF1NP

3

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-02-02, 22:27:45 »

congrats, Juan Carlos 

73
Willi

4

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-01-28, 20:25:36 »

Hi Juan Carlos,

nice pictures. Congrats and good luck.

73
Willi

5

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-01-27, 09:43:48 »

One turn (360 degrees) = 100 pps. The 500 pps by my former encoder (HEDGE) was too much. That was the reason I changed to 100 pps. Pushing the small encoder you also can change the speed of the external encoder.

73
Willi

6

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-01-26, 19:28:10 »

Hi Juan Carlos,

No resistor necessary.

Btw. look at this:
http://dk8jg.de/VFO-Maus-3.pdf

73
Willi

7

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-01-26, 11:03:40 »

Hi Juan Carlos,

Some pictures for wiring the 100 pps decoder:
A goes to internal decoder (red)
B goes to internal decoder (green)
OV goes to GND (yellow)
VCC goes to + 5V (orange)
A and B you can change
The colors belongs to the wire in the RC-2000 case not at decoder.

73
Willi

8

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2021-01-24, 20:01:06 »

Hello Juan Carlos,

In the meantime I changed my Hedges Encoder to this one:

https://www.amazon.de/Terminal-Klemmen-Elektronische-Handrad-Impulsgeber/dp/B07GCGWDHW/ref=sr_1_13?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=encoder&qid=1611609055&sr=8-13

73, Willi

9

Hardware, Cabling, Installations / Re: Audio from Flex1500/3000 using RRC1258

« on: 2020-06-14, 18:26:06 »

Hello Karsten,

I also use Remoterig together with my Flex 6400. Audio and cw is way more faster than via SSDR!

Look here for some solutions on Flex Radio Community:

https://community.flexradio.com/flexradio/topics/how-to-add-remote-contest-capability-to-flex-6000-without-a-remote-pc
https://community.flexradio.com/flexradio/topics/my-proposed-remote-smart-sdr-setup-will-it-work-obvious-problems

73
Willi, DF1NP

10

General discussion forum / Re: Twin setup for TS-2000

« on: 2018-07-24, 16:21:57 »

Hi Mike,

Look here:
http://www.remoterig.com/forum/index.php?topic=1076.0

gl Willi, DF1NP

11

Feature Requests / Re: External key / external Elbug

« on: 2017-05-10, 19:08:22 »

Hi Roland,

I use ETM 9c keyer.
Conf. and wireing look manual 1258 MK-II cw-keying: I/0 Connector control and radio RRC.

73
Willi

12

General discussion forum / Re: KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-10, 18:57:13 »

Hi Per,

Congratulation! Happy to hear all is working now. 

73
Willi

13

General discussion forum / Re: KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-06, 15:48:13 »

Hi Per,

My conf. for profil CAD:

Serial settings control:

COM1 mode  Mode-7, CAT to COM2 (remote)
COM1 baudrate 9600   
COM1 8   
COM1 stop bits 1
COM1 parity 0 - Off
COM1 rts/cts  Yes   
COM1 terminator (hex)  00
Use USB Com Port as COM1 No 
   
COM2 mode Mode-4, Kenwood, Yaesu, Elecraft   
COM2 baudrate  9600   
COM2 data bits  8   
COM2 stop bits 1   
COM2 parity 0 - Off   
COM2 terminator (hex) 
Use USB Com Port as COM2  Yes   
   
COM3(Extra) mode (USB-COMFSK) Inactive

Radio:
Serial settings

COM1 mode  Mode-7 CAT to COM 2
COM1 baudrate  9600   
COM1 data bits 8   
COM1 stop bits 1   
COM1 parity 0 - off   
COM1 rts/cts  Yes   
COM1 terminator (hex) 
   
COM2 mode  Mode-4, Kenwood, Yaesu, Elecraft   
COM2 baudrate 9600   
COM2 data bits  8   
COM2 stop bits 1   
COM2 parity 0 - Off   
COM2 terminator (hex) 

Radio autoconnect: yes

For ARCP-590 you first must install the virtual comport drivers.

good luck
Willi

14

General discussion forum / Re: KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-05, 19:54:00 »

Hi Per,

Normaly I am using TS-590 TWIN (very  comfortable). But I also can work by CAD. So the settings for HRD  is: Kenwood, TS-590, COM (look at your device manager), speed 9.600, no: CTS, DTR, RTS.

Using ARCP is a little bit tricky, hi. Speed 9.600, comport as above.

I prefer working with USB cable: seriel setting: USB comport as COM 2: yes

73
Willi

15

General discussion forum / Re: KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-05, 17:33:46 »

Hi Per,

For configuration look at RRC 1258-MKII user manual, page Kenwood general.
http://www.remoterig.com/downloads/RemoteRig_RRC1258-MkII_Users_manual.pdf

You also can use ARCP-590 vers. 2.02 freeware program by kenwood. http://www.kenwood.com/i/products/info/amateur/ts_590/arcp590_e.html

73
Willi