Messages

16

General / Re: Samsung S6 and Nano

« on: 2015-06-12, 17:20:23 »

Hi Roland

Thanks for the explanation and info, I will check the website regularly

73 Rune LA7THA

17

General / Samsung S6 and Nano

« on: 2015-06-12, 00:42:42 »

Hi All

I just got my new Samsung S6. Try to install Nano for Kewnood as i use With my S3. I cant find the service APP. After some Reading i found this :"I'm afraid that native android SIP stack is not enabled on Nexus 6.. I Guess this is the same problem on my new S6?. Is there a work around this problem?.

73 Rune LA7THA

18

General discussion forum / RRC > antenna switch 1269 and web switch via IP

« on: 2015-06-10, 10:41:31 »

HI Remoterig

Anyone that can answer my question below.

73 Rune

My RRC1258 and antenna switch via IP is working excellent. I wonder if there is any plan to let the web switch talk to the system via IP. I am running Acom 2000 on web switch and could be nice if the web switch “Talk” the same language. This would get the Acom 2000 amp to follow the radio and antenna via IP.

73 Rune LA7THA

19

General discussion forum / Re: KX3 as the controller

« on: 2015-01-18, 18:10:25 »

Mitch

Is elecraft doing any further work on this?, I remote ctrl my KX3 via the serial com1 and using TRX-Manager.  However if elecraft is doing more work on this I think I will invest in another KX3 :-) I like my TS480 but when listening on 160cw and using receiving antennas I prefer my KX3 :-)

73 Rune LA7THA

20

Configuration, RRC 1258 / use of Virtual ports / softports.

« on: 2015-01-10, 09:45:36 »

Hi All

Remote location.
Radio RRC Version MKIIS TS480 in use, CAT from TS480 RS232 connection to com2 in RADIO RRC.
Latest FW version 2.83 installed.

Control end
RRC Version1, latest FW version 2.83 in use. RRC Version 1 has only Com0 and COM1 physically installed in RRC box.
I am using the USB cable between RRC and my PC and in device manager I get 4 com ports.

RRC1258 COM0 (COM7)
RRC1258 COM1 (COM8)
RRC 1258 COM2 (COM6)
RRC1258 COMExtra (COM9)

Are all these soft comports supported by RRC Version1? I have try to connect TRX-Manager to com 2 (virtual port/ Softport control end) and have try to select the different settings in RRC radio and also RRC control but not able to connect TRX-manager “inn parallel” for frequency update to my logging program. Anyone that have similar program HRD, or any other logging program connected and used this way.

I have also used com1 virtual / soft port and try different setting but no luck so far.

I found this in the user manual, i dont see that comX

COM1 can be connected to the USB interface instead
of the RS-232 interface if your PC do not have
traditional com ports. When installing Microbit Setup
manager a virtual Com port called “Microbit RRC
Virtual Comport (COMX)” is installed. That’s the one
you should connect to when using HRD or other
softwares.

73 Rune LA7THA

21

General / license

« on: 2015-01-09, 09:09:22 »

Hi

When you purchase license for Nano, will this work on several Android devises or do you need to purchase a new licens for each type of device or if you select i.e. Kenwood and / or Elecraft.
I have tested my Elecraft  KX3 on com2 and using RRC Micro,  seems to work fine. Will this also work when using Nano.

73 Rune LA7THA

Update 14JAN2015

KX3 is now supported and running on K3 Nano APP. Tested on my mobile phone Samsung s3 and also my Galaxy Tab4. I will say particularly the Nano on my tab4 is a must for a serious DX`er that will check for DX when “surfing the sofa”  

73 from a happy remoterig customer.


 

22

General discussion / Re: RRC Micro with RRC Radio MK2S

« on: 2015-01-09, 07:45:58 »

Hi All,

From front page @ remoterig.com, this sorted my problem :-)

"Due to some problems with the Serial Radio Communication between RRC-Micro and the Radio that seems to have been introduced in version 1.6.13, we recommend to use 1.6.12 until the problem is solved."

I was using the latest version (1.6.16) when i test, went pack to 1.6.12 and all is good :-)

73 Rune LA7THA

23

General discussion / Re: RRC Micro with RRC Radio MK2S

« on: 2015-01-08, 08:34:09 »

Hi Mitch

Thanks for quick ans. My settings is as you mentioned, com2 in Radio RRC 9600, 8,N,1, terminator 0 and the same in RRC Micro Client software.
I made my own serial cable RADIO to RRC Radio pin 2>2, 3>3, 5>5 pin 7 and 8 is shorted on Radio 9 pin plug still no luck, will check again after work today and see if there is anything I have done wrong.

73 Rune LA7THA 

24

General discussion / RRC Micro with RRC Radio MK2S

« on: 2015-01-07, 22:51:55 »

Hi All

I just received my RRC MK2S and have configured to work with my TS480 using the front panel.
I try to activate my RRC Micro but no luck. When I was using my RRC Micro with my old RRC Radio Ver1 i used com1 in Radio RRC, mode4 4800Kbs. In RRC Micro client software I also used com1 mode4 4800 Kbs.

What com port should i use when using the New RRC Radio MK2S?. From what i find in the document i should use com2 in Radio RRC and also com2 in RRC Micro client software. What is wrong? Any suggestions?


73 Rune LA7THA

25

General discussion / Re: CW from RRC Micro

« on: 2014-12-26, 14:52:28 »

Hi All

It all worked fine when using ARCP 480, but when sending CW from RRC Micro I could not hear CW side tone. I found the “problem”, TX Monitor is one thing but if RTP TX mode in Radio RRC is not set to Continuous I was not able hear the generated CW in Radio. Now all is nice and pretty    I have to say thanks to my friend LA9KKA that pointed me that way.

73 Merry –Xmas, Rune LA7THA

26

General discussion / CW from RRC Micro

« on: 2014-12-19, 23:35:35 »

Hi All,

I was told that CW function in RRC Micro was using the side tone from Radio, not produced in RRC Micro dongle.
I have listening to myself via web SDR and can hear that I send cw as normal. I have checked side tone in radio and all is ok. I am still not able to hear any side tone when sending cw.

I try to use ARCP 480 software from Kenwood, when using this software there is also a cw function via Keyboard. When I use this software I can hear my side tone as normal and i also send cw out as normal. Is there anyone else that has seen the same problem? is thre anything else i have done wrong. Using W7 64 bit system and RRC Micro Client 1.6.12BETA2.

73 Rune LA7THA

27

General discussion / Re: Com issue RRC Micro

« on: 2014-12-19, 13:36:57 »

Hi

Debug log sent for RRC Micro ver 1.6.1.15.0 and 1.6.12.BETA2

73 Rune LA7THA

28

General discussion / Com issue RRC Micro

« on: 2014-12-18, 23:56:55 »

Hi All,
Hi have tried to sort out a com issue with RRC Micro version, xxxx.13, xxxx.14 and the latest xxxx.15.
If I use RRC Micro version 1.6.12.0 BETA2 all is working as normal. I just start the RRC Micro client software and all is working fine. I can start and stop, exit TRX-Manager start again and all is as normal.

If I use RRC Micro version 1.6.13.0, xxxx14 or xxxx15 I can always start the RRC Micro then connect using TRX-manger. I can open the cat port and close it all day long and it work. If I EXIT TRX-Manger and start TRX-Manager again and try to connect with Cat, I can send the command but the radio will not update any i.e. frequency etc. Sometimes I get and errors say “port already open”. If I Exit TRX-Manager, EXIT RRC Micro, rebooting the PC and start again I can always connect the first time but as soon as I have EXIT TRX-Manager ones the problem comes back.
Is this related to my PC? If I uninstall and install RRC Micro client 1.6.12.0 BETA2 all is back to normal again. I will leave this to the experts I have spent 10-15 hours and this is my final result. Is there anyone that is using RRC Micro with similar problem?
I am uisng W7 64bit and latest firmware in RRC Radio.

73 Rune LA7THA

29

General / Re: Nano on RRC Version 1

« on: 2014-12-14, 13:50:46 »

Thanks

73 Rune LA7THA

30

General / Re: Nano on RRC Version 1

« on: 2014-12-12, 07:57:04 »

Hi

I am using Version1 of the RRC (Silver type housing) I guess they have com0 ("display com port") and com1 serial port where my TS480 is connected. If i understand this correct its version2 of RRC  that have com0, com1, com2 . The ports are the  same as in my control RRC when i am using my Kenwood TS 480 front panel. 

73 Rune LA7THA