Messages

31

General discussion forum / Re: Antenna switch over IP

« on: 2014-12-07, 07:11:05 »

Problem solved, the IP function is not implemented in Version 1 of the RRC boxes (Silver type)

73 Rune LA7THA

************************************************************************
10th JAN.2015
I have a new RRC MKIIS now on remote (RADIO RRC) and my antenna switch is working verry nice :-)

73 Rune LA7THA
************************************************************************

32

General / Nano on RRC Version 1

« on: 2014-12-06, 09:05:14 »

Hi All,

I installed Nano on my Samsung S3 mobile phone. Seems I get the Sip working at least that is what RRC Radio main page is reporting. My system is working with RRC micro using PC and TRX-Manager via CAT. Cold this problem be relate to Version 1 of RRC since I can’t connect to COM2

73 Rune LA7THA

33

General discussion forum / Re: Antenna switch over IP

« on: 2014-12-05, 12:40:29 »

Kenwood TS480

34

General discussion forum / Re: Antenna switch over IP

« on: 2014-12-05, 12:36:39 »

Hi Mike

I am using KW480 and i try different settings. When select Kenwood IF the radio goes dead stop working.
Also the auto selection on main page is done.

I can send you log in page and username and password in an email.

73 Rune LA7THA

35

General discussion forum / Antenna switch over IP

« on: 2014-12-04, 23:12:34 »

Hi All
I just received my antenna switch 1269 and have configured it to "talk “on my network.
I can manually switch antenna and seems to do that just fine. I have tried to use the IP function between the RRC Radio and antenna switch. Settings in antenna switch are:

Antenna switch configured with IP address as in Radio RCC (192.168.1.120)
Ports are the same in RRC and antenna switch 13010. I have not been able to get the antenna switch to follow the Radio/Radio RRC.

I have also used Micro RRC and TRX-Manager to see if RS232 port is working and that work just find. Suggestions are welcome.
Using the latest software in RRC Radio and antenna switch.

Seems that info gets updated in RRC Radio see Copy and paste from Radio RRC below.

Antenna -Switch (IP) 192.168.1.70/13010

73 Rune LA7THA

36

Configuration, RRC 1258 / Re: No connection between RRC Control and Radio

« on: 2014-11-23, 14:54:36 »

Hi All

I found the problem in RJ45 connector (client/ local RRC box) one wire that was broken.


73 Rune LA7THA

37

Configuration, RRC 1258 / Re: No connection between RRC Control and Radio

« on: 2014-11-15, 09:30:47 »

Hi Mike

The com0 settingas are 57600, i have sent you the file in html format in a seperate email. I am not allowed to attach them as html or bin here.

73 Rune LA7THA 

38

Configuration, RRC 1258 / Re: No connection between RRC Control and Radio

« on: 2014-11-15, 00:13:02 »

Hi, I will resending the files tomorrow when I am back in the shack.

73

Rune LA7THA

39

Configuration, RRC 1258 / No connection between RRC Control and Radio

« on: 2014-11-14, 22:43:32 »

Hi All,
I have just start to connect my Remoterig system again after QRT for 14 months. I have upgrade to the latest firmware on RRC Control and RRC Radio unit. I am using version 1 of the Remoterig boxes. I have attached export of all settings as html for Control unit and radio unit. I am using KW TS480 and I try to connect this up all on the inside of my router so fire walls and port forwarding should not be a problem. actually I am using patch cable from remote rig boxes direct in to the lan port of my router. I have connected the display of my TS480 direct to the radio and I can switch power on/OFF no problem. When I connect all cables etc and try to connect there is absolute nothing that happens. Cable from Front panel TS480 to RRC control box front AUX port, then LAN cable to my router. From RRC Radio unit LAN cable direct to my router, Front RS232 on RRC box direct to KW TS480 com port (9600 baud) and RRC Radio AUX port (6pin RJ45) to KW TS 480 Panel socket. (6 pin RJ45)

IS there anything that have changed regarding sip ports etc on latest firmware or similar.

See attached export of my settings. Rename the file back to html, was not allowed to send them as html so I change the name to .jpg just convert back again should work I hope.

73 Rune LA7THA

40

General discussion forum / Re: RC1216 used for Acom amp , antenna rotor and displayed in a web interface

« on: 2013-07-01, 16:07:06 »

Hi Mike

Thanks for info

73 Rune

 

41

General discussion forum / Re: RC1216 used for Acom amp , antenna rotor and displayed in a web interface

« on: 2013-06-30, 21:09:41 »

Hi Joni


I gues the answhere to this has to come from the remoterig software programers.

73 Rune LA7THA

42

General discussion forum / RC1216 used for Acom amp , antenna rotor and displayed in a web interface

« on: 2013-06-27, 00:56:18 »

Hi

I can see that RC1216 is used for Acom amp, IR, ant rotor and display the data in a web interace.
LP-100 watt meter from Larry N8LP is used here for measure power. Is it posible to use the RC1216 for the same purpose as for the Acom amp and so on. Is this a mather of some "WEB interface programing?". Is there anyone that have an watt meter where it display power in a web interface ?.

73 de LA7THA 

43

General discussion forum / Re: DIGIMODES - RRC1258MkII - TS480SAT

« on: 2012-09-27, 20:23:27 »

Hi

I will try this, thanks for help and info.

73 Rune LA7THA

44

General discussion forum / Re: DIGIMODES - RRC1258MkII - TS480SAT

« on: 2012-09-24, 22:06:25 »

Hey

Did you find any sulution on this one, i have done the same, i also only get a carier when i transmitt. Out0 on remote RRC is set to RTTY > to pin 8 (From ts480 usermanaul, RTK RTTY (FSK) keying input. Ground this terminal to alternate Mark and Space.) Out1 is Keyer (and it work) Out2 is set to PTT > to pin 3 (from ts480 manaual, Ground this terminal to transmit. ANI (DATA connector) terminal turns OFF)

any help please

73 Rune la7tha

45

General discussion / Re: PC client

« on: 2012-03-04, 23:51:36 »

Hey

Thanks for info, will check again the next week

73 Rune LA7THA