Author Topic: FT-100 hardware mods?  (Read 6762 times)

k5dog

  • Newbie
  • *
  • Posts: 8
    • View Profile
FT-100 hardware mods?
« on: 2013-01-04, 00:16:19 »
From an old post:

Yes RRC1258MkII ver 7 can be used to remote the FT-100, but I have not had time to update the manual yet. It may take some time as Im on vacation now.


73 de mike

I have an RRC1258MkII Ver 5.  Can I use that with the FT-100 if I do the FT-857 hardware mods?

Tnx,
Steve-dog, k5dog

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: FT-100 hardware mods?
« Reply #1 on: 2013-01-04, 09:49:07 »
Hi

Here are instructions about how to use the FT-100

http://www.remoterig.com/wp/?page_id=1704

73 de mike

k5dog

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: FT-100 hardware mods?
« Reply #2 on: 2013-01-04, 14:37:13 »
Hi

Here are instructions about how to use the FT-100

http://www.remoterig.com/wp/?page_id=1704

73 de mike

Thanks Mike.
« Last Edit: 2013-01-05, 18:21:54 by k5dog »

k5dog

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: FT-100 hardware mods?
« Reply #3 on: 2013-01-05, 19:03:20 »

I am having a hard time understanding why the power on/off switch (FT-100 Front Panel and Radio  Pin#4)  connects to ground on both ends (TTL connector Pin#1)?  How can this cause the RRC's to connect?

Thanks
Steve, k5dog

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: FT-100 hardware mods?
« Reply #4 on: 2013-01-05, 19:52:01 »
I have not have time to check your email. There can be errors in the drawings, but no one have told me before.

I hope I will have time tomorrow

73 de mike

k5dog

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: FT-100 hardware mods?
« Reply #5 on: 2013-01-05, 21:53:29 »
Mike,

Yes, there is an error in the drawings.
On both FT-100 connectors Pin#4 should connect to TTL Pin#6 instead of Pin#1
Also on both units, Pin 1 of P5B (which is connected to TTL Pin#6) should have a jumper to "PWR SW" P5B Pin#9.

When those things are changed, the FT-100 seems to work very well.

Probably very few FT-100 users now, and of those, very few have the extender kit required.
I personally use several of these radios at remote locations, and I greatly appreciate your work on this radio.

Thanks again.

Steve, k5dog 

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: FT-100 hardware mods?
« Reply #6 on: 2013-01-05, 22:59:28 »
Ok

If you have verified it, I will change the drawings. I do not have a radio to test with I borrowed one. I might find my paper notes to compare with but Im not shure.

Thank you for the clarifications

73 de mike

k5dog

  • Newbie
  • *
  • Posts: 8
    • View Profile
Re: FT-100 hardware mods?
« Reply #7 on: 2013-01-05, 23:15:34 »
I have made the changes that I described above, and now the radio is working well.




sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: FT-100 hardware mods?
« Reply #8 on: 2013-01-05, 23:27:25 »
I just checked and my drawings are correct for RRC V7, but there need to be additional drawings for earlier versions where the FT-857 mods are done. In V7 TTL pin 1 can be released from GND by removing JMP5, then TTL pin 1 is only connected to P5A 9 which is jumpered to PWR SW on my drawings.

So I removed the text about using earlier versions until I have made more drawings.

73 de mike
« Last Edit: 2013-01-05, 23:29:22 by sm2o »