Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - LA7NO

Pages: 1 [2]
16
Hardware, Cabling, Installations / Re: USB driver
« on: 2016-01-15, 14:21:14 »
I tried Version 1.30 and it worked just fine. :-)
I also noticed that some other errors were corrected.
Thanks.

Keep up the good work.

Regards & 73,

Per-Tore
LA7NO

17
Hardware, Cabling, Installations / Re: USB driver
« on: 2016-01-15, 12:52:33 »
Version is 1.28.

It shows up in the Human Interface Devices section.
But also in the Ports section with status stating driver not installed.

When I try to do an automatic driver update, I get this error:
    "A service installation section in this INF in invalid"

Please refer to attached screen shots.

I tried it on a Windows 10 machine with no problems.

P-T

18
Hardware, Cabling, Installations / USB driver
« on: 2016-01-15, 11:04:56 »
Hello,

I am not able to get the USB connection to my 1216H working.
It seems that there is a USB driver problem.
The Setup Manager does not see the switch.

I am running Windows XP Pro SP3 fully updated.

Regards,

Per-Tore
LA7NO

19
Configuration, RRC 1258 / Pulse settings
« on: 2015-10-31, 14:32:31 »
I can not find the explanation for the "pulse settings" referred to in 'Set Relays' menu.
Please refer to the screen shot.

P-T


20
General discussion forum / Re: IC-7100 problem
« on: 2015-10-21, 22:20:46 »

Could the cuse of these problems be reduced availability of the Remoterig DynDNS service?

I assume this is only beng used during initial setup of the connection. After that, it will work fine as long as a reset is not performed.

Anyone else experienced something similar?

P-T

21
General discussion forum / Re: IC-7100 problem
« on: 2015-10-21, 21:26:06 »
UPDATE #2:

After several tries with full power off/on of  everything, it is now up and running again.

Odd!

P-T

22
General discussion forum / Re: IC-7100 problem
« on: 2015-10-21, 21:00:53 »
UPDATE:

Tried it again, but this time I've not been able to get it up and running again.

I can connect to both the Control-RRC and the Radio-RRC and look at status etc. All looks normal, except that the SIP status on the Control-RRC is "Unknown (1)". After resetting the Control-RRC, SIP status is again "Idle". But as soon as Ipress power-on on the IC-7100 panel, SIP status goes to "Unknown (1)" again.

P-T

23
General discussion forum / IC-7100 problem
« on: 2015-10-21, 20:19:52 »
Hello list,

I have had my setup working nicely for a couple of days now. It is a standard configuration with IC-7100 radio on one RRC and the control unit on another RRC. The Radio-RRC is connnected to the router with Ethernet cable. The Control-RRC is connected to a 4G GSM mobile router (ice.net Smartrouter). I am using DynDNS and DHCP as described, and the router is setup with port-forwarding. So, the connection will be really remote, and not on the same local segment.

All works very well. However if I turn off power on the Control-RRC without first powering off the IC-7100 via the control panel, then things go wrong. Afer powering-up the Control-RRC again, nothing seems to works. It seems that the only solution is to reset the IC-7100 radio unit by powering it off and on.

Any clues anyone?

Regards,

Per-Tore
LA7NO





Pages: 1 [2]