Messages

76

General discussion forum / Re: RRC1258 MKIIs

« on: 2023-09-10, 14:10:35 »

Hi
You need one Control-RRC (the one with CW-knob) and one Radio-RRC to make it work.

The hardware is different so you need to find a Radio-RRC

https://butik.limmared.nu/en/remoterig/4619-remoterig-1258mkiis-radio-unit.html

73 de mike

77

Configuration of Routers, Firewalls, etc / Re: FT-857 To IC-7100 change over.

« on: 2023-09-08, 17:25:41 »

Hi
send export settings (html) files from both units to support2remoterig.com so I can have a look
73 de mike

78

General discussion forum / Re: SSB suddently dropped out

« on: 2023-09-04, 19:41:28 »

OK Great

It has happen a few times, there is no known reason for it

73 de mike

79

General discussion forum / Re: SSB suddently dropped out

« on: 2023-09-04, 12:56:39 »

Check codec out gain settings in the radio RRC

Mike

80

General discussion forum / Re: Pair TWO control boxes to radio

« on: 2023-09-01, 09:22:00 »

Hi
It's common to use more than one Control-RRC to one Radio-RRC. Only one can use the radio at the time.

73 de mike

81

General / Re: RRC NANO i Cannot be used normally

« on: 2023-08-31, 17:23:52 »

If the radio works with RRC-micro the CI-V cable and RRC settings is ok, but select com1 in the app

73 de mike

82

General / Re: RRC NANO i Cannot be used normally

« on: 2023-08-31, 10:49:46 »

Hi
what kind of CI-V interface do you use ? You must have a CI-V interface which have a separate power supply, the RRC cannot power the CI-V interface. Normally the CI-V interface is connected to Com2 as the Com2 has male dsub (same as a PC).Com1 has a female dsub and pin2 and 3 are reversed. But com1 can be used but both the app and the RRC must be configured for using com1  and the CI-V must have have pin2 and 3 crossed. You will not hear any audio until CI-V connection is working as the IC-7100 start with volume =0.

73 de mike

83

Configuration, RRC 1258 / Re: Ts480 will not switch to transmit

« on: 2023-08-30, 08:04:09 »

emails is still not deliverable

Your email address is the same as registered on the forum but still not OK

failed: host ff-ip4-mx-vip2.prodigy.net

.. Addressee unknown,

mike

84

Configuration, RRC 1258 / Re: Ts480 will not switch to transmit

« on: 2023-08-29, 22:31:47 »

I tried to anser your email but it can't be delivered

/mike

85

General discussion forum / Re: Elecraft K4 with RemoteRig

« on: 2023-08-29, 18:33:37 »

Hi

No v 2.95 is still the latest published version

https://www.remoterig.com/wp/?page_id=79

73 de mike

86

General discussion forum / Re: RRC dont communicate

« on: 2023-08-25, 16:39:32 »

Hi
send export settings (html) files from both units to support@remoterig.com so I can have a look

73 de mike

87

Hardware, Cabling, Installations / Re: connessione rrc a k3s

« on: 2023-08-23, 19:32:04 »

I doubt the K3s RJ45 is numbered the same as the dsub. You need to check the Elecraft docs I have not checked.

Mike

88

Allmänt diskussionsforum / Re: Remoterig MkII och Icom IC-7100

« on: 2023-08-23, 01:07:22 »

Hej

har du provat att minska uteffekten maximalt eller att sända i en konstlast och testa om problemet kvarstår. Det låter ju som om du får RFI från antennen när du sänder.

Micke

89

General discussion forum / Re: Intermittent Audio

« on: 2023-08-21, 19:46:15 »

Hi

Remoterig doesn't know or care about 4G, 5G etc. Can't you setup the router to use 4G if the 4G signal is stronger. or set the router to use a fixed band that you want to use, maybe a lower frequency band is better

73 de mike

90

Hardware, Cabling, Installations / Re: connessione rrc a k3s

« on: 2023-08-18, 07:33:39 »

Hi

You need RJ45 to  9 pin D-Sub adapter cabels from Elecraft E980297. I thougt they where delivered with the K3S but maybe not anymore.

73 de mike