Messages

16

Configuration, RRC 1258 / Re: N1MM CAT Control and Keying

« on: 2012-09-05, 18:54:37 »

Hi Mitch,

I have the K3 Twin set-up (K3/0 -> K3/100). Works great on Phone. I don't do CW but would like to try RTTY. I have (almost...) everything setup. RX works, but the TX wont. MMTTY keys the radio but there are no modulation going out.

Any suggestions?

73 de Adde, SM0SHG

17

Configuration of Routers, Firewalls, etc / Re: IC7000

« on: 2012-08-13, 15:24:36 »

You can't use it like the IC-706 or TS-480 (front/radio separated).

See this old post: http://www.remoterig.com/forum/index.php?topic=81.msg220#msg220

Regards,

Adde

18

General discussion forum / Re: solar powered, unmanned station

« on: 2012-08-12, 08:39:08 »

Hi,

It works just fine. After a power outage my system boots up just fine. The only thing that is different is the IP adress I get from the network operator but since I use Remoterigs DDNS it's no problem either.

73 de Adde

19

Allmänt diskussionsforum / Re: RRC Micro, sliter med å komme på nett.

« on: 2012-06-25, 09:32:35 »

Dessutom kan 5060 vara spärrad i vissa routrar då denna ofta är låst som standardport för ip-telefoni av operatören. I min Tele2 4G router gick inte denna att använda... När jag bytte till 5061 gick det dock utmärkt.
Adde

20

General discussion / Re: U.S. Availability

« on: 2012-06-14, 22:21:55 »

Any particular reason why the Micro-PC Client is not available from HRO in States? The 1258's along with the acc cables are.

Would likely buy one if it was!!

Cheers!
LLoyd
VE3ERQ

The RRC-Micro is a great product. Why not get it from Microbit? Shipping cost can't be that bad.

http://shop.microbit.se/webshop/catalog/index.php

73 de Adde, SM0SHG

21

Configuration, RRC 1258 / New in 2.38... "Elecraft advanced"

« on: 2012-06-01, 15:09:46 »

Hello,

Under the "Advanced settings" menu there are now a setting called Elecraft advanced"... Can't find any ref. in the manual for this one. What is it for?

Regards,

Adde

22

General discussion forum / K3/0 -> K3/100 Known bugs?

« on: 2012-06-01, 11:54:46 »

Hi all,

I have now set up my K3/0 and K3/100 with the Remoterig K3 Twin units. Everything seems to work great. Does anyone know about bugs in the system? I'm thinking of bugs in the Elecraft FW...

Mitch, you are a power user... Have you noticed any bugs?

73 de Adde

23

General discussion forum / Elecraft K3 Twin and RRC Micro?

« on: 2012-05-28, 22:05:33 »

I have the Electraft K3 Twin products and about the set them up.

When I'm "on the road" I want to use the RRC Micro with HRD to control my K3 on the remote site. Will it "just work" or do I need to change anything in the set-up?

73 de Adde, SM0SHG

24

General discussion / Re: Kenwood TM-D710 and RRC-Micro PC Client

« on: 2012-03-14, 21:14:41 »

What control software did you plan to use?
73 de Adde, SM0SHG / SH0G

25

General discussion forum / Re: What about this?

« on: 2011-12-20, 21:36:25 »

And when can we expect an app for iPhone?
Adde

26

General discussion forum / Re: N1MM Voice keyer with Remoterig?

« on: 2011-12-18, 15:03:26 »

Thanks... Two more quedtions then... What type of isolation, and where on the PC do you take the PTT signal?
Adde

27

General discussion forum / Re: DIGIMODES - RRC1258MkII - TS480SAT

« on: 2011-12-16, 13:48:10 »

And the solution was??
Regards,
Adde

28

General discussion forum / N1MM Voice keyer with Remoterig?

« on: 2011-12-12, 22:28:34 »

I would like to use N1MM's voice keyer with my TS-480. To control the radio with N1MM is no problem... But how do I get the radio to "play" the WAV files? Do I just connect the computer audio-out in paralell with the mic input on the local RRC? Or is there any smarter way to do it?
Regards,
Adde

29

General discussion forum / Re: IC706MK2g and Computer control via HRD

« on: 2011-12-12, 10:39:18 »

You will need a CI-V cable between the radio and the remoterig unit.
Regards,
Adde

30

Hardware, Cabling, Installations / Cable-set for IC-706MK2G

« on: 2011-12-09, 18:22:53 »

Hello,

Does anyone now if there is a "ready to go Remoterig cable-set" for the IC-706MK2G? Looking especially for the "control head separation cable"... The one with the ICOM proprietary connector... Yes, yes, I know, it's easy to cut and solder... Well, I don't want to solder. I want to buy...

Regards,

Adde