Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sm2o

Pages: 1 2 3 [4] 5 6 ... 201
46
Konfiguration av RRC 1258 / Re: RRC 1258 portnumrering
« on: 2023-11-16, 15:17:34 »
Nej det har ingen betydelse

Som  jag sa så är det bara viktigt att det är samma i båda ändor och att det är mellan 0-65535 ( dvs 16 bitar har inget med RRC att göra)

/micke


47
Konfiguration av RRC 1258 / Re: RRC 1258 portnumrering
« on: 2023-11-15, 17:38:12 »
Det funkar med vilka portnummer 0 -65535 som helst bara det är samma i bägge ändar. Vissa kan vara reserverade i routrar osv. Om man har fler än 1 Radio RRC bakom samma router måste alla portnummer vara unika

73 de micke

48
Hardware, Cabling, Installations / Re: No Tx Audio
« on: 2023-11-12, 10:24:14 »
Hi
8V is available at the second pin from right at the strapping socket when the connection is up. Check with an volt meter. So you can put a wire from there to the correct RJ45  pin. I looked for a schematic to the mic but did not find any, just a instruction where  the Yaesu connector shown is wrong. So if you use a cable with that pinning it will not work. You will make a new cable or change the positions of the red wires in the Control-RRC

UP and DWN button will not work

73 de mike

49
Hardware, Cabling, Installations / Re: No Tx Audio
« on: 2023-11-11, 21:28:49 »
If a mic works connected direct to the FT-857 doesnt mean that it works with the Remoterig as with the MH-59 as the Remoterig doesn't have any 5V out

73 de mike

50
Hardware, Cabling, Installations / Re: No Tx Audio
« on: 2023-11-11, 20:24:28 »
 HI

What kind of mic do you use ? It must be standard  simple MH-31. The MH59 need 5V power which Remoterig do not supply.

If you already have the MH-31 check the red wires and the codec gain settings

73 de mike

51
Konfiguration av RRC 1258 / Re: RRC 1258 portnumrering
« on: 2023-11-10, 10:48:36 »
svar på ping behövs inte

Vilken mode man använder spelar ingen roll, Control-RRC kommer helt enkelt inte i kontakt med Radio-RRC

skicka export settings (html) filer från bägge till support@remoteig.com så får jag kika.

slå av SIP ALG i bägge routrarna om det finns en sån inställning

port 13000-13001 är UDP tänk på det oxo vid portforward

/micke

52
Konfiguration av RRC 1258 / Re: RRC 1258 portnumrering
« on: 2023-11-10, 09:14:40 »
Det finns ingen begränsning i vilka portnummer man kan använda, men jagg tror inte det är där problemet ligger

Det behövs ingen portforwarding på kontrollsidan och Telnet port skall aldrig forwarderas.

Är du säker på att du har publik  ip- address på radiosidan ? Det är det vanligaste problemet idag. Tele2 tog bort publik IP på en massa mobilabonnemang i veckan

Så här gör du för att kolla det

http://www.remoterig.com/wp/?page_id=3494

73 de micke


53
General discussion forum / Re: Icom ID-5100 or Yaesu FTM-6000R Compatability
« on: 2023-11-10, 09:09:09 »
Sorry but there is no support for these radios

73 de mike

54
General discussion forum / Re: TS-590S Twin setup: No memory channels or split operation
« on: 2023-11-09, 17:16:34 »
Hi

The TS-590 twin fucntion was introduced 2014, I can't belive that no one has noticed that split is not working since then.

We do not have any TS-590 so we can not test

73 de mike

55
General discussion forum / Re: Connection to remote lost every 30 seconds
« on: 2023-11-08, 16:31:04 »
Hi

pingtimes of 780 ms will no cause disconnection but interuption in the audio stream and respons when tuning.

You have to investigate your internet connection, there is nothing that can be done in Remoterig to solve the problem.

Try to move the control-RRC to an other location so you can find out in what end the porblem is

73 de mike

56
Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output
« on: 2023-11-08, 11:46:47 »
if you have the orginal Elecraft cables I think it's connected to the back mic connector so you need to switch back to rear mic in the K3 setup

By the way It's better to connect the mic direct to the Control-RRC, Less noise

email me export settings(html) files from both units to support@remoterig.com

/mike

57
General discussion forum / Re: Modes 6 & 7 (CAT to COM2) doesn't support all CAT commands?
« on: 2023-11-06, 15:16:11 »
Hi

When transferring kenwood CAT commands Remoterig does not interpret the messages  it just use the ; (semicolon) which indicates the end of message to initiate transmission of a packet

73 de mike

58
General discussion forum / Re: Webswitch Advanced Settings - Elecraft K3?
« on: 2023-10-29, 19:55:48 »
Hi

use Kenwood(IF)

you can use the manual för as-1289, the control part is the same, just different hardware

http://www.remoterig.com/downloads/AS1289-Users_manual.pdf

73 de mike

59
General discussion forum / Re: Yeasu 3000
« on: 2023-10-29, 17:05:44 »
Hi

All radios with a analog CAT port can be used, RS232, CI-V etc. There is a few new radios which only have USB CAT, they can not be used.

You can test how it will work if you connect a serial cable (RS232 ) from the PC to the radio without Remoterig. If you do not have a RS232 port at the computer you can use a USB to serial converter.

73 de mike

60
General discussion forum / Re: Need help
« on: 2023-10-29, 12:45:37 »
Hi

send export settings (html) files from both units to support@remoterig.com

73 de mike

Pages: 1 2 3 [4] 5 6 ... 201