Messages

1

Configuration, RRC 1258 / WiFi not present

« on: 2025-08-08, 15:23:27 »

Mike,

I've owner the RR system since 2016, just got " WiFi module not Present" .

IT seems from this thread "Old wifi board and new RRC-1258 MKII" that means it's not working anymore?

Opened case to 1258 Radio pulled it out and but it back, same message!

Does Remote Rig still sell them!

Bruce W4HI

2

General discussion forum / New Icom 7100 compatible with exsiting remote rig pairs

« on: 2024-01-08, 18:46:36 »

Hello from W4HI,

I want to upgrade my exsiting IC-7100 to the newly manufactured IC-7100.

Current remote rig pairs:
Control / Remote 1258 V7 HW 8 Software 2.95 Boot 113 Compiler 4.6.2.

Will I have any issues using the NEW 7100 currently in production with existing remote rig pair?

Bruce W4HI

3

Configuration, RRC 1258 / Re: "failed Getting SW version"

« on: 2021-05-07, 02:42:28 »

Hello Mikale,

Thanks for the reply on both forum requests, I looked them over briefly, but will get into them very soon, I appreciate your support.

LOVE your summer house!

Bruce W4HI
Fair Play, SC

4

Configuration, RRC 1258 / Unable to connect to RR control to built-in Wi-fi

« on: 2021-04-27, 21:07:29 »

Hello Everyone,

This problem has recently started being unable unit to connect to remote RR radio via RR built in Wi-Fi module. It's been working fine for several years.

I've checked both Wi-Fi user and passwords I've been using and they are correct.

Once selecting the various RR Radio unit I want to connect with I get the following error:

Name   Value
P5.4   ON
Radio   ON
Connection status   Faulty(See below)
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   Error(0)
SIP command timeout   0
Rx Jitter buffer size   8
Rx Jitter delay   6
Dual Rx   0
Current audio packet size   20
Current audio quality   2 - Linear 16 bits 8 kHz
SIP Out port   13000
SIP In port   13000
Audio Out port   13001
Audio In port   13001
Command Out port   13002
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   98.233.8.147

If I connect via wired Ethernet works fine.

Have changed Ethernet cable from RR Control to my IC-7100 control head same results.

Wi-Fi settings

Wi-Fi settings
1: Name (SSID)   
Pixel_7565
1: Password (PSK)   
parker18
 Hide
    
2: Name (SSID)   
linksys2
2: Password (PSK)   
parker18
 Hide

There is another post from W4HI not being able to connect using MB Setup v2.065 to RR Control unit, do not know if they are connected.

I've never had this issue before, would appreciate some assistance.

Bruce Marron W4HI

5

Configuration, RRC 1258 / "failed Getting SW version"

« on: 2021-04-27, 20:44:40 »

Hello Anyone,

Recently I've had several bewildering issues with my RR Control unit.

I've been owner RC1258's since 2009 and never had these issues. Current RR 1258 purchased in 2016 so I'm stumped.

Name   Value
Company   Microbit
Product   1258
PID   4
Version   7
HW   8
Software   2.91
Bootloader   1.13
Compiler   4.6.2
Build   Jun 16 2016 07:13:13

First issue: Can't read Control unit with MB 2.0 v1.31 with two different USB cables. Just upgraded MB 2.0 to v2.06 same result.

Failed getting SW version: Failed opening the device:
Device connected!
Failed getting SW version: Failed opening the device:
Failed opening the device:

The other strange issues are related to my profiles. I have access to two other RR radio's which have been working flawless for several years now.

Will address then in later posts.

Thanks Bruce Marron W4HI

6

General discussion forum / Re: cannot connect control box to radio box all of a sudden

« on: 2020-04-02, 17:34:09 »

Hello Mitch,

Thanks for the quick response. I'm helping him diagnosis the problem remotely through Team viewer, K3HP is a IT specialist.

We've tried to connect locally but that didn't work either. But will check you recommendation later today, he's at work today.

Bruce W4HI

7

General discussion forum / cannot connect control box to radio box all of a sudden

« on: 2020-04-01, 18:37:38 »

My partner K4HP has a remoterig system identical to mine. His system has been work flawless for years without issue.  All of a sudden we are unable to connect over the internet or able to connect via his LAN.  He has checked the internet, cable, router, and connect other equipment using the radio box IP with success so this should rule out the internet and hardware.  He has checked the IP address and it is correct for trying to access the radio remote rig box.  What is strange is that he sees the setup of the radio and control box both via a web browser by accessing the correct IP address's respectively on the local network. Has his radio box gone south?

K3HP has just applied registration as a user of the forum.

Thank in advance Bruce W4HI.

8

General discussion forum / Re: No audio when transmitting using RRC1258MKII v 2.91 / IC 7100

« on: 2019-06-13, 22:41:41 »

Hello Mike SM20 and VK3ALB,

Mike it was the codec gain setting had "changed" from 255 on remote box to 0, changed it back to 255 works great.

Thanks Bruce W4HI

9

General discussion forum / Re: No audio when transmitting using RRC1258MKII v 2.91 / IC 7100

« on: 2019-06-12, 21:20:00 »

Thanks for the quick feedback, will try these ideas
Bruce W4HI

10

General discussion forum / No audio when transmitting using RRC1258MKII v 2.91 / IC 7100

« on: 2019-06-11, 20:16:13 »

My two friends and I have three RRC 1268 MKII systems using IC-7100’s setup for several years now. User 2 remote station recently stopped transmitting audio, but you still have fully control of remote 7100 of HF VHF & UHF just carrier comes up but no audio?

I’ve checked all parameters in both User 2’s control and remote boxes including IC 7100’s they are all seem to be right, only User 2 remote system does not have audio on TX.

W4HI (me) user 1 can connect to User 3 and TX/RX with audio, as well as User 3 connect to my station and TX/RX with audio.

Any words of wisdom would be appreciated Bruce W4HI.

11

General / RCC Nano license requirements for control of other persons RRC Radios?

« on: 2018-02-19, 18:24:00 »

Hello,

My trial license has expired (f741).

Two other Amateurs friends have recently purchased IC7100's and RRC remotes. I want to be able to use the RCC Nano Android app on their radios also.

But before I buy the license I need to know if I need anything else?

Bruce W4HI

12

General / Re: Icom RRC Nano "license expired"

« on: 2018-01-12, 21:40:48 »

Me too, researching how to get license, anybody know how?
Bruce W4HI

13

General discussion forum / Re: RCC Radio box losses Web server

« on: 2017-12-29, 15:05:25 »

Mitch DJ0QN / K7DX

Couple of things, I was using the WAN Static IP address on Control box for Radio box connection, changed it to the LAN Static IP on Radio Box seemed to improve. I know once I go Remote with control box will have to change it back.

Also found using the WAN DNS 75.75.75.75 instead of the Comcast router DNS of 10.0.0.1 it works more reliable??

Even when I can reach the Radio box with the Webserver, still cant ping the Radio Box that is odd?

Leaving on a trip for two weeks, set a timer to reboot Radio three times a day for now.

14

General discussion forum / Re: RCC Radio box losses Web server

« on: 2017-12-29, 03:43:19 »

Thanks for the reply, I will check that out. W4HI Bruce

15

General discussion forum / RCC Radio box losses Web server

« on: 2017-12-28, 19:04:15 »

Hello,
Just purchased RRC-1258 MkII system for IC 7100.

Followed manual and programmed both Radio box and Control box with IC 7100 Control module inside. Version 2.91 in both units. Using Wired Ethernet while on LAN for testing, and diagnosing issues or using RR Wi-Fi for control and wired Ethernet for WAN operation system functions. Also have RR 1332 CI-V installed on Radio box. System is using manual suggested setting for IC-7100 operation.

Using Ethernet switch in shack to Comcast router/modem a distance away, which is providing Static WAN IP and DHCP for Control box.
My issue is system works well for a randomly time both on LAN (Radio & Control) or WAN operation. Suddenly IC-7100 display freezes and then shuts off. If I go to a PC on the LAN I can’t reach the Radio Box static IP LAN address (10.0.0.226).  If I Ping it comes back unreachable. IF I press on/off switch on IC-7100 Display it doesn’t turn back on.

To resolve issue, have to reboot Radio box and control box, then it is allowing turning on IC-7100 display and can go to PC on LAN see Webserver page for Radio box.

Thanks for your advice W4HI Bruce