Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - k6jv

Pages: [1]
1
General discussion forum / RRC not been seen on network
« on: 2022-12-13, 02:22:02 »
Setting up a new pair of RRC. Worked fine on the bench but when I powered everything back up the unit at the radio end does not appear to be on the network. Rebooted the router and the green light on the
unit is solid green but it does not show up on the network, just the control end. Is there a way to reset the radio end or has something died?

2
General discussion forum / Kenwood TM-V71A
« on: 2022-08-03, 14:08:49 »
I know there is diagrams for the TM-V71 are the connections the same for the TM-V71A?

3
General discussion forum / Yaesu G-450A, RCU, and Webswitch
« on: 2015-11-22, 23:13:56 »
Has anyone had any experience interfacing the Yaesu G-450A rotator with the RCU and Webswitch?

4
The manual does not show how to strap the AUX/MIC connector for the ID-880. Is it the same as the IC-2820?

5
Hardware, Cabling, Installations / Re: IC-880
« on: 2012-01-30, 15:08:51 »
I ordered the mic adapters for an IC-2820, then changed to the IC-880. Are the adapters the same or do I have to order new ones.

6
Hardware, Cabling, Installations / IC-880
« on: 2012-01-30, 01:10:09 »
Do hardware modifications need to be done to RRC-1258 units before the radio will even turn on via LAN. Have wired but unable to control radio remotely.

7
Hardware, Cabling, Installations / TTL Connector
« on: 2012-01-29, 21:46:29 »
What size is the TTL connector. Does not appear to be standard 6 pin RJ-25

8
Configuration, RRC 1258 / Re: can not update firmware
« on: 2012-01-29, 03:20:06 »
Also get this error:

Size mismatch, header size=1347093252, rxd size=162747!

9
Configuration, RRC 1258 / can not update firmware
« on: 2012-01-29, 02:37:07 »
I have tried everything, three different computers, I get a error code 31, both trying web and usb. I need the new firmware as the one installed 002.028 does not support the ID-880H. These units were just purchased from HRO yesterday.

10
General discussion forum / Icom 2820
« on: 2010-08-23, 18:39:10 »
Has anyone successfully remoted an Icom IC-2820 Dstar radio?

Thanks,

Doug
K6JV

11
General discussion forum / Re: Power light flashing
« on: 2010-07-03, 23:18:09 »
Dyndns cancelled by dns name due to inactivity. Reassigned and working again.

12
General discussion forum / Power light flashing
« on: 2010-07-02, 03:08:44 »
Remote has been working fine, all of sudden power light flashes and can not control radio. The IP is still valid as I can use the browser to get into the remote (192.168.1.227). If I remember the flashing lights means it has not picked up an IP address. I even changed it to DHCP and connected directly to cable modem and got the same response.

Ideas?

Thanks,

Doug
K6JV

13
General discussion forum / IC-706 Motorboating
« on: 2010-05-16, 02:12:31 »
Transmit audio motorboats, both into dummy load and outside antenna. When remote connected directly to radio, audio is fine.

Currently I have to use a powerline ethernet connection to have internet on that side of the radio room. Is it possible RF is getting into the powerline or ethernet powerline adapter?

Has anyone used the powerline ethernet adapter in this type of application?

14
General discussion forum / Re: startup issues
« on: 2010-05-12, 02:12:43 »
Got it working, was SIP issue, not probably set.

15
General discussion forum / startup issues
« on: 2010-05-11, 21:08:46 »
Trying to get my remote IC-706 Mark IIG going.

Completed cable, with extender, works fine.

Setup both boxes as shown.

Forwarded proper ports.

Setup DynDNS account.

Radio does not turn on remotely. I have two different IP addresses as home. Control is on one, radio on the other.

What should I start looking for?

Thanks,
Doug
K6JV

Pages: [1]