Topics

1

General discussion forum / RRC-1258 Control DHCP on

« on: 2016-01-10, 17:32:31 »

Hi there!
If I am switching on the DHCP at RRC1258 Control then I will get a IP address from my local router.
Unless I don't find out the IP address given by my router I cannot access the RRC1258 Control.
Is there a given URL name that makes it possible to access easily to my RRC1258 Control without knowing the given IP address?

Thanks in advance
Mike

2

Configuration, Webswitch 1216H / RC-1216H Webpage connection

« on: 2013-03-29, 23:51:56 »

Hi
I am using the RC-1216H for controlling the SteppIR antenna via the SteppIR controller (DATA IN/DATA OUT interface).
If I am opening my webbrowser (IE or Google Chroma) I can access the webpage of the RC-1216H. But after a while (about 15 secs or so) the green Online LED on the webpage stops blinking and restars after a while. It seems that the RC-1216H looses the connection to my browser or the 1216H Webserver hangs up. How can that be???

Even with the WebSwitch 1216H I have the same problem. After I have connected the Webserver of the WebSwitch I am loosing the remote connection and I have to restart (reload or open the webpage again) the webpage.

It is really annyoing and I don't have any idea to solve that problem.
Thanks for your  help!
Mike

3

Configuration, RRC 1258 / Strange behaviour

« on: 2013-03-09, 13:46:35 »

Hello!
I managed to configure the Radio and Remote RRC-1258MkII and it works on my local network.
The Control RRC finds the Radio RRC and I can connect to the Radio RRC.

If I place the Radio RRC to my remote station at my shacks place something goes wrong.
I test my RRC equipment with LogMeIn remote login.
If I connect to the Radio RRC the yellow LED on the Radio RRC (AUX/MIC) goes on (SIP connection OK) and the LEDs on my Ethernet switch and Radio RRC (green Ethernet LED) are flashing (means Ethernet pakets are transfering from ADSL Modem to the switch and to the Radio RRC) .

BUT just a few seconds later the ADLS router on the remote site will be blocked and I cannot access to the Ethernet.
If i try to start the Internet browser I will not get a connection to the Internet. If i check the status of the Radio RRC it seems to be ok (no errors) although the Ethernet is blocked.
The Ethernet connection to the ISP will be blocked and sometimes I get even a new IP address from my ISP.
That means to me that the ADLS router hangs up and at startup I will get a new IP address from my ISP.

Is it normal that the Ethernet LEDs (green) on the Control and Radio RRC blinks quickly?
And I have seen on the Radio RRC that the Audio IN and OUT Ports and the Command IN and OUT ports are not the same. When I try my RRC set up at local network at home the IN/OUT ports for Audio and Command are the same (11000, 12000). 
I am using the ports 11000, 12000, 5070 for the connections.
A remote access to the Radio RRC webpage is possible. That means the IP address of Radio RRC is sent to the dynamic DNS.
The Radio RRC is in the DMZ of the ADLS-Router with a fix IP address. I tried to do a port forwarding with port 11000, 12000 and 5070 but the result was the same (as mentioned above).
I try to do the setup without connected radio (Elecraft K3) to be sure that only the RRC could be the problem.

All other remote rig is working perfectly well (rotor, SteppIR antenna).

Please could anybody help me? I have not the faintest idea what the problem could be! And I already wasted a lot of time to manage the problem without results.

Thanks a lot
Mike