Author Topic: Cannot Reach Radio-RRC  (Read 12503 times)

WA5KSC

  • Newbie
  • *
  • Posts: 4
    • View Profile
    • Email
Cannot Reach Radio-RRC
« on: 2012-06-18, 15:40:16 »
Hello,

I cannot reach the Radio-RRC remotely by entering the DDNS address.  I have described below.

I recently purchased a pair of RRC-1258MkII’s.  I have performed the “Step by Step System Setup” successfully through Step 18.  However, Step 19 fails.  I cannot reach the Radio-RRC remotely. 

A little more detail to help:

The Radio-RRC s shows:

Info:

Name   Value
Company   Microbit
Product   1258
PID   4
Version   5
HW   6
Software   2.59
Bootloader   1.9
Compiler   4.6.2
Build   Jun 5 2012 15:31:54
ROM/RAM   432112/56408
ETH-RAM   2944 (max 3kB!)
ResetSrc   0 [3]
Uptime   436769
Serial number   4696
MAC address   00:1e:fd:01:88:f8
IP address   10.0.0.228
Netmask   255.255.255.0
Gateway   10.0.0.1
DNS   10.0.0.1
Wi-Fi network   module not present

Status:

Name   Value
Radio   OFF
Connection status   Disconnected
SIP status   Idle
Last SIP error   None
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
External IP    68.nnn.nnn.nn
SIP Out port   5060
SIP In port   5060
Audio Out port   0
Audio In port   0
Command Out port   0
Command In port   12000
External SIP In port   5060
External Audio In port   11000
External Cmd In port   12000
Other party   0.0.0.0
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status
OK
Ping status (watchdog)   Off
DNS status   OK, remoterig.com = 193.202.110.185
Active profile:   Default
PTT status:   OFF

DDNS Status shows:
HTTP/1.1 200 OK Date: Mon, 18 Jun 2012 13:00:14 GMT Server: Apache/2.2.22 (Mandriva Linux/PREFORK-0.1mdv2010.2) X-Powered-By: PHP/5.3.14 Content-Length: 106 Connection: close Content-Type: text/html

My Own Host Name that I tried remotely is:

xxxxxxxx.ddns.remoterig.com

Regarding my network on the Radio RRC side:

I have a DSL Modem with a public IP of “68.nnn.nnn.nn” 

The DSL modem presents “192.168.1.64” to my Netgear Router.

The LAN side of the Netgear Router starts with “10.0.0.1”

I have the Radio-RRC IP at “10.0.0.228”

I have the Radio-RRC defined as the Default DMZ Server in the Router.


What am I doing wrong?





« Last Edit: 2012-06-21, 00:35:07 by WA5KSC »

WW2DX (Lee)

  • Jr. Member
  • **
  • Posts: 42
    • AOL Instant Messenger - ljimber
    • View Profile
Re: Cannot Reach Radio-RRC
« Reply #1 on: 2012-06-18, 16:20:38 »
Good Morning,

What seems to be happening is your DSL moden is doing NAT for you already. What you really want to do is call your DSL provider and ask them how to configure your DSL modem to be in "Bridge Mode". This will pass the public IP to your Netgear router. The other option is to see if you can log into your DSL modem and then configure the ports to be forwarded to your netgear router, but you are just adding another layer of complexity and you start jumping through hoops.

Let me know if you make progress here.

73, Cheers!

Lee
WW2DX

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Cannot Reach Radio-RRC
« Reply #2 on: 2012-06-18, 16:20:49 »
Just a guess: you probably left the radio RRC's configuration page at port 80. This would likely
conflict with your router and maybe another device in your network. Change your web port
and try it again, this time xxxxxxxx.ddns.remoterig.com:XXXX, where XXXX is the new port.

I also highly suggest that you change SIP from port 5060 to something else. This port is
blocked by many routers for VoIP use.

73,
Mitch DJ0QN / K7DX
« Last Edit: 2012-06-21, 10:47:50 by dj0qn »

WA5KSC

  • Newbie
  • *
  • Posts: 4
    • View Profile
    • Email
Re: Cannot Reach Radio-RRC
« Reply #3 on: 2012-06-18, 18:16:09 »
I am currently at the RRC-Radio site.  I did try the changing the web configuration port from 80 to 8080 since is was the quickest thing to try.  Works fine within the network using nnn.nnn.nnn.nnn:8080.  Externally, using someone else's network, I tried the DDNS with :8080 appended as suggested.  I still just get a hang (no response).  I am researching the other suggestions received so far.

WW2DX (Lee)

  • Jr. Member
  • **
  • Posts: 42
    • AOL Instant Messenger - ljimber
    • View Profile
Re: Cannot Reach Radio-RRC
« Reply #4 on: 2012-06-18, 18:34:05 »
Yep, makes perfect sense. Think of it as having two netgear routers "daisy chained" and the first one is not allowing your ports to be forwarded. Since you have your own Netgear device then just have the provider switch their device into bridge mode. Your goal is to make their device invisible to your Netgear router looking at the internet.

Hope this helps.

Lee
WW2DX

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Cannot Reach Radio-RRC
« Reply #5 on: 2012-06-18, 18:41:40 »
Actually, port 8080 was not a good decision....it is used by many routers for remote admin.

I understood you that the system was working ok, just that you couldn't reach the RRC's web
admin page. I read down enough to notice the double-NAT problem before that Lee mentioned.
Assuming the system is otherwise not working, then you do need to pass through the
other DHCP server as Lee mentions.

73,
Mitch DJ0QN / K7DX

WA5KSC

  • Newbie
  • *
  • Posts: 4
    • View Profile
    • Email
Re: Cannot Reach Radio-RRC
« Reply #6 on: 2012-06-19, 17:38:01 »
Quick update.  Putting the modem in Bridge mode and moving the PPoE to the router now allows me to reach the Radio-RRC web server which is sitting in the router DMZ.  I really appreciate everyone's help, and I will post a final update when I get back to the Contol-RRC location. I just noticed that I probably posted this message in the wrong section of the Forum.  My issue related to the RRC-1258MkII and not to the Webswitch. 

WA5KSC

  • Newbie
  • *
  • Posts: 4
    • View Profile
    • Email
Re: Cannot Reach Radio-RRC
« Reply #7 on: 2012-07-01, 15:51:21 »
Everything is working fine now.  I had a final issue of the Control RRC PWR LED continually blinking. 

I could login to the Control RRC from the LAN, but could not go any further with connecting to the Radio RRC.  I could, however, successfully connect the Control RRC to the internet by directly connecting the Control RRC to the DSL modem.  I eventually gave up and switched out my old D-Link router to a Netgear unit similar to the one at the Radio site. 

I want to thank everyone for their help. 

73,
Steve