Author Topic: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??  (Read 7789 times)

Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
I have the basic TS480SAT working through the internet now plus a webswitch for turning on/off power supplies and resetting.  Does anyone have any experience with using the Elecraft amp and autotuner with the RRC com ports?  The mode selection info is not very clear to me.  I also want to use HRD with the 480 but no computers at the remote site. Can you use HRD with com0 and the amp and tuner on com1 and com2?  Both amp and tuner have remote control software operating via RS232. 

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #1 on: 2013-05-14, 13:26:44 »
Com0 is used by the TS-480 control panel, COM2 are normally used for the CAT control, that leaves COM1 to be used for controlling the PA. It's possible with the Expert 1K-FA and 2K-FA but I have never tested with the Elecraft PA.

73 de mike

Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #2 on: 2013-05-14, 15:20:06 »
All right thanks.  The two Elecraft units have simple control programs for computer control via RS232 so hopefully
I can just use a DB9 switch on Com1 switched by the webswitch. I will try it here when I get to that point.

Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #3 on: 2013-05-19, 02:54:51 »
Has anyone got one of these to work over COM1?  Radio is a TS480 and the radio mode is 5.  Using the Elecraft supplied cable direct from a KAT-500 tuner to a gender changer on COM1 on the radio RRC.  Using a straight serial cable from COM1 on the control RRC to the compiuter.  The control program works fine direct from tuner to computer.  I have tried a LOT of different settings and nothing works. Only TX and RX are used. 

Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #4 on: 2013-05-19, 14:03:33 »
I guess I need a null modem gender changer.   

Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #5 on: 2013-05-29, 02:32:24 »
I have either the KPA500 or  KAT500 working through com1 over the internet.  I had to use the menu on the KPA500 to change its speed to 38400.  The setting is just serial setting 4 and using a null modem gender changer at the radio RRC, with the TS480 turned on.


Beck

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #6 on: 2013-05-29, 04:52:19 »
I tried com1 and com 2 both at setting 4 and can control the KPA500 via com1 and the KAT500 via com2 simultaneously over the internet.  No room for CAT.

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: HRD, Elecraft KPA-500 amp, Elecraft KAT-500 tuner??
« Reply #7 on: 2013-05-30, 15:20:32 »
I you need CAT, then move one of the other devices over to any standard serial server,
such as from Lantronix or Moxa. I have my stations all running using these devices.

73,
Mitch DJ0QN / K7DX