Messages

16

Konfiguration av RRC 1258 / Re: IP setup problem

« on: 2023-07-18, 20:17:53 »

Mello Mike

myipaddress show
Your Hostname:
152.156.165-134-dynamic.movinet.com.uy

Router Status
Active LinkWWAN1
Uptime2 days, 00:09:01
IP Address152.156.165.134/255.255.255.252
Gateway152.156.165.133
DNS200.58.141.163 200.58.157.11

now is working, BUT I didnīt changed anything!. Will see when it stop working again

thanks!

73,
Jorge

17

Konfiguration av RRC 1258 / IP setup problem

« on: 2023-07-18, 19:19:04 »

Hello

I know this was discusses many times, but I couldnīt figure out who to solve it.

I have K3/0 Mini and remoterig boxes working perfectly on the SAME network

My internet link to the station broken, so I installed another internet system at the station

So now I have diferent networks on both sides

I have a dyndns service, I setup it on the remote router and I add it on my local remoterig settings (192.168.0.169)

Sometimes it worked, but now is not working, so i think is this IP changing but I couldnīt figure out how to have it working

I apreciate any help to set up it

thanks in advance!

73,
Jorge
CX6VM/CW5W

18

Configuration of Routers, Firewalls, etc / Re: Amper 2000 4L DDNS help

« on: 2021-10-06, 18:42:05 »

hello Mitch

I start over

I did that, but on http://ddns.remoterig.com/status/index.php I received Microbit DDNS Result xxxxxxx not found!

So seems remoterig dynamic dns service is not working?

73,
Jorge
CX6VM/CW5W

19

Configuration of Routers, Firewalls, etc / Re: Amper 2000 4L DDNS help

« on: 2021-10-06, 12:43:39 »

hello Mitch

before that I have a link to the station to send internet, so I was in the same network, radio and control where in the same network, no need to configure DDNS

Now I have two diferents networks. The main one in my house, and a new one (Movistar 4G router) in the remote site.

I tried to configure DDNS, but I am not good at this point and couldnt yet have it working

73,
Jorge
CX6VM/CW5W

20

Configuration of Routers, Firewalls, etc / Amper 2000 4L DDNS help

« on: 2021-10-06, 02:10:49 »

hello

I change my remote internet provider with Movistar Amper 2000 4L router like this one https://www.robustel.com/en/product/r2000-vpn-gateway/

I do all the configuration but couldnīt find where to setup DDNS to access it from other network. Movistar support on my country didnnīt give a solution yet, so I want to know if someone can help me to tell me where to register my tplinkdns on this router

thanks in advance!

73,
Jorge
CX6VM/CW5W

21

General discussion forum / Re: TURN ON K3/0 Mini REMOTELY

« on: 2019-09-05, 23:18:44 »

Hello Mitch

this is very interesting!, will look for some Youtube video to see how it works

But, no time for this now, i am leaving tomorrow.

Is there any way to turn on the control radio from 192.168.0.169?

thanks,
Jorge

22

General discussion forum / TURN ON K3/0 Mini REMOTELY

« on: 2019-09-05, 23:05:27 »

HELLO

I want to know if itīs possible to turn on remotely, maybe through local remoterig box, the radio that I use for control side, Elecraft K3/0 Mini

I will travel, but I donīt want to carry my control side equipements (K3/0 Mini, remoterig, paddles, Mic), so thinking that if I can turn on my K3/0 Miini, I can do CW with N1MM+, using TeamViewer to access my control site laptop.

I donīt want to keep the radios ON for a week, so I need to turn on it anyway

thanks!
Jorge
CX6VM/CW5W

23

Configuration, RRC 1258 / Re: K3/0 mini - K3S Twin setup Term on K3/0

« on: 2019-09-01, 19:21:34 »

Hello

I want to share a solution that seems is working for me.

I couldnt go to remote site to try some ferrites on cables, but I read a note from Elecraft about Audio quality on Radio Settings on remoterig configurations

When I had the problems, I have Audio quality = 8 - linear 16 bits 16 khz

I changed it, i used Audio quality = 5 but problem persist although last more time to apear.

Finally I am using  Audio quality = 3 Alaw 12 khz and is working very good, no more problem with lost connection with remoterig boxes

73,
Jorge
CX6VM/CW5W

24

Configuration, RRC 1258 / Re: K3/0 mini - K3S Twin setup Term on K3/0

« on: 2019-08-27, 00:04:18 »

Hi Mitch

today I was playing on FT8 on 15 meters, and no problems with remoterig, K3/0 Mini WSJT-X

Now on 160 meters, with 300 watts, and again the problems.

So i am thinking maybe some RFI problem getting into radio remoterig AUX/MIC connector? That could be possible?

I will go to remote site and add some ferrites to this cable going to remoterig box

73,
Jorge
CX6VM/CW5W

25

Configuration, RRC 1258 / Re: K3/0 mini - K3S Twin setup Term on K3/0

« on: 2019-08-25, 00:05:49 »

yes Mitch

remote radio and control radio (K3/0 Mini) are in 38400

73,
Jorge

26

Configuration, RRC 1258 / Re: K3/0 mini - K3S Twin setup Term on K3/0

« on: 2019-08-24, 15:13:48 »

HELLO!!

I did a search about this problem.

I was using two K3/100 and never happened to me to see that the TERM does not go away and the remote K3 display does not show

10 days ago I got a K3/0 Mini with factory cable RRMINICBL and I started often to see that the TERM does not go away and the remote K3 display does not show

So the problem may be is a bad RRMINICBL  cable?

thanks!
Jorge
CX6VM/CW5W

27

Hardware, Cabling, Installations / Re: K3S & K3/0 & wsjt-x - do I need COM2?

« on: 2019-08-16, 02:49:23 »

thanks you very much Mitch!

Always quickly to help, obviously is my fault, never do digital but people are moving to FT8 :-(

73,
Jorge
CX6VM/CW5W

28

Hardware, Cabling, Installations / Re: K3S & K3/0 & wsjt-x - do I need COM2?

« on: 2019-08-16, 00:40:13 »

Hello Mitch

I go directly to the laptop, once I had it working, I use the soundcard

finally I got it. Today I received a PDF file from Elecraft, Digital Operation with K3-0 Remote System v-01.pdf

I found that I had bad settings on my radio Remoterig

I had in IO SETTINGS

OUT0 mode   :   connect
OUT0 on/off   .   OFF

OUT1 mode   :   I/O
OUT0 on/off   .   OFF

OUT2 mode   :   keyer
OUT0 on/off   .   OFF

so I changed it to

OUT0 mode   :   connect
OUT0 on/off   .   OFF

OUT1 mode   :   baudot-RTTY/45
OUT0 on/off   .   OFF

OUT2 mode   :   keyer
OUT0 on/off   .   OFF

And now WSJT-X is working :-)

73,
Jorge

29

Hardware, Cabling, Installations / Re: K3S & K3/0 & wsjt-x - do I need COM2?

« on: 2019-08-15, 18:31:31 »

hello

I bought a K3/0 Mini, and I have a problem to run WSJT-X

I have a cable from K3/0 Mini SPEAKER to Laptop MIC and other cable from K3/0 Mini MIC to Laptop HEADPHONES

I can decode signals, but is impossible to have a transmittion. K3/0 Mini put on TX, but no bars on ALC meter

Any idea what I am missing?

thanks!
Jorge
CX6VM/CW5W

30

General discussion forum / Re: buying WiFi interface

« on: 2019-05-08, 01:31:03 »

thanks very much for the help!

73,
Jorge