Topics

1

General / RRC nano K-PRO doesn't have sound

« on: 2024-01-12, 16:10:38 »

Hi all,

I'm a proud user of RRC Nano for Kwd for 5 years. I haven't had any problem until now. Recently I have changed my phone, an old Nokia 7.2 with Android 11 (Android One) to a One Plus Nord 3 5G. This device uses Android 13 with OxigenOs 13.1.

I have been using flawslesly my RRC Nano K in my old phone for 3 years, but when I have installed the App in my new phone, it doesn't work.

The symptoms are:

- I can connect to my device (Kwd TS-2000)
- I can control it
- I can transmit, and the audio goes out.
BUT I have no receive audio. I can't hear anything. There is a total silence.

I have read carefully the forum, and I have to say that I'm using the last version 1.6.6 and all permissions are given to the App.

Any suggestions or ideas on what might be going on?

Thanks a lot in advance.

BTW.- If I use my old phone, where the App is still installed, all works perfect. I connect my old phone via Wi-Fi to my new one and I have audio.

2

General discussion / FT8 or digital modes in RRC-Micro PC Client

« on: 2019-09-18, 17:13:10 »

Hi everybody.

First of all I have to say that I have taken a look in the forum to try to find an aswer to this question, but I have found several threads, but any works well here.

At the beginning of the summer I bought a RRC-Micro PC client wich has been working flawlessly since then. I have bought another one for my wife, because sometimes I'm out home, and she can control our remote station without problems. We use, as well, the RRC-Nano APP, and we must honestly say that it's a great tool, and it works very very well (I would like it was able to transmit CW, but I'm sure it'll do it in a future) so, as you can read, I have some experience now with this envirorment.

However, I can't use  my RRC-Micro with my FT8 program (I'm used to using JTDX, but I can use WSJT, if it's necessary) I have read several threads in this forum, and I have done the configurations I have read, without succes, so I would like to know what I have to do, because I have read the manual, and the information for two RRC-1258MkIIs is very clear, but I haven't found any configuration for the RRC-Micro in the manual.

Can anyone tell me some advice?

Thanks a lot in advance.

Best regards.
Luis, EA5KY

3

General discussion / Problems with ARCP-2000

« on: 2019-07-04, 22:32:09 »

Hi everybody.

I'm new with Remoterig, and  before writing, I have read a lot in this forum and on the Remoterig web page trying to find a solution to my problem.

I have RRC1258MkII in one end (Radio End) and a RRC Micro at the other end. Both can speak without problems, but when I try to connect my ARCP-2000 (I execute it with Administrator rights) it can't connect to my TS-2000 that's on the other side. I have tried as well with HRD, and I have found the same problem. I have looked for on the Internet, and I have read several times the manual (both, RRC 1258MkII and RRCMicro), and I can'T find the solution to this problem. I have checked my COM ports in both sides, and all is right, because RRC1258MkII and RRCMicro can speak, but I can't control my TS-2000 because I can't run my ARCP-2000 or the HRD.

I enclose five files,

- The first one shows my Virtual Comm Ports configuration (I have used your tool Microbit Device Manager)

- The second one shows other the Debug I made when I try to connect my ARCP-2000 to the other side.

- The third one shows my RRC1258MkII serial settings

- The fourth one shows my RRC1258MkII Radio settings

- The fiveth one shows my RRCMicro settings

I'm going to go to Ireland next week, and I would like to use my TS-2000 during my free time, so any advice will be welcome, because I don't know what I have to do.

Thanks a lot in advance.

Regards.
Luis, EA5KY