Messages

61

General discussion forum / Re: Elecraft KPA500 Amp

« on: 2012-11-28, 09:19:20 »

Hi Mitch

As usual, always ready to help…!! Unfortunately not a K3 but TS-480 connected to KPA500 + KAT500

Ziv

62

General discussion forum / Elecraft KPA500 Amp

« on: 2012-11-27, 14:08:14 »

Hi

Anyone have experience with Elecraft KPA500 & remoterig?

thanks

Ziv

63

General discussion forum / Audio is not transferring from MIC connector using PTT-VIA-CAT

« on: 2012-11-04, 11:55:21 »

Hi

I am using TS-480 and Mix-W software. CAT is working ok via com2. When I work PSK, I can manual activate PTT and audio from PC via the microphone jack and all works ok. However, when am using PTT via CAT Command, the radio do KEY to TX but no audio is transferring.

Do I must use the PTT via mic jack send the Audio?

Thanks

4Z4OQ Ziv

64

General discussion forum / Re: What Radio?

« on: 2012-11-04, 11:43:15 »

Hi Stuart

The 857 is a nice small rig to go. If you very basic user it will be ok. For more complex use, you will need the user manuel handy, because the radio HMI is not the best

Enjoy

Ziv - 4Z4OQ

65

General discussion forum / Re: easy rotor com1 mod?

« on: 2012-10-27, 02:11:07 »

thanks willi. however my com2 is CAT control and i am looking to control the rotor via com1... are setting the same?

66

General discussion forum / Re: easy rotor com1 mod?

« on: 2012-10-26, 20:16:40 »

this is what i got.... i am looking to know the mode setting of com1 of the rrc at both ends

67

General discussion forum / Re: easy rotor com1 mod?

« on: 2012-10-26, 13:07:41 »

i am using old cde ham 4. without remoterig direct connection all worked ok in 4800 but cant make it run with rrc 

68

General discussion forum / easy rotor com1 mod?

« on: 2012-10-26, 10:43:50 »

Hi
i am installing easyrotor via com1 - what should be the mode setting at control side and radion side

Thanks

4z4oq

69

General discussion forum / TS-480 cat issues

« on: 2012-10-23, 11:24:37 »

Hi

I am using TS-480 and RRC + MixW software and have two issues:-
1.    CAT is working ok when Radio is connected locally / directly from computer to radio via FTDI USB to RS232 adaptor connected only with 3 wires. (pins 2,3,5/ TX,RX,GND). However, via RRC (com2) it don’t work. Changing between pin 2&3 did not help to solve the problem.
2.   I know my settings are ok, because changing to different USB to RS232 with full d-sub connector CAT is working ok. However, here is got a strange situation that when I push Microphone PTT (SSB mode) the radio is sending short beeps every 1/2 sec..
When is am disable CAT the beep stops.
I attached here a zip sound file so you can listed to the scenario

Any idea??

70

General discussion forum / Re: config cw paddle - solved

« on: 2012-10-03, 12:32:37 »

Hi All

Cable was found ok. i had to play with configuration of I/O & Keyer seeting until found configuration that works. See attached

71

General discussion forum / Re: USING remote rig to control power & access.

« on: 2012-09-24, 10:04:03 »

Guy - it looks like the ball is back in your court... can you post the info again..?

72

General discussion forum / Re: USING remote rig to control power & access.

« on: 2012-09-21, 21:24:28 »

Hi Jan

Here is just one sample of URL... Try to open the attachment file

http://www.remoterig.com/forum/index.php?topic=365.msg1118#msg1118

73

General discussion forum / Re: config cw paddle

« on: 2012-09-04, 15:05:55 »

The original 3.5mm cable will be instale at the remote site tonight or max tomorrow and i will adv...

Meantime, a lot of thanks to Mitch for his time and help!!

74

General discussion forum / config cw paddle

« on: 2012-09-02, 17:15:42 »

Hi
I need some help to configurate my paddle in cw mode. i was trying for 3 3 hours several sets of configuration with no luck.  The manuel is not so clear to me and i got mixed between paddle and keyer configuration.
My set-up is simple. Ts-480 split between panle & radio/ 
I connect one lever paddle to the control RRC with 3.5mm plug (paddle works fine on my ts950) and on the remote side i got 3.5mm plug to plug cable.
What need to be my configuration of (keyer& I/O) in control and what on radio - Also do i need to connect the plug to plug cable in the radio side to  pad or straight socket?

thanks for help
Ziv

75

General discussion forum / Re: dyndns - solved

« on: 2012-08-27, 14:38:50 »

Found DNS ruter configuration was wrong.