Author Topic: K3 + K3 and no connession  (Read 12991 times)

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
K3 + K3 and no connession
« on: 2014-02-02, 15:25:07 »
GooD morning OM

Before to go crazy I am writing to solve my "Remoterig" problem
2 Elecraft K3 connected to the network via a home router
These are the radio setting
-------------------------------------------------------------------------
RADIO

Radio settings

Program mode   Elecraft twin
Sip password   no passw.
Sip contact   192.168.0.227
Auto connect   no
Audio quality   
Codec out gain   
Codec inp gain   
Codec inp HPF Hz   
Codec inp preamp   38400
COM0 baudrate   8
COM0 data bits   1
COM0 stop bits   0
COM0 parity           2
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0 no

Status
Name   Value
Control panel   ON
Radio   ON
Connection status   Disconnected
SIP status   Unknown(1)
Last SIP error   None
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   0   
------------------------------------------------------------------------------------------
CONTROL SETTING

Program mode   K3 TWIN
Sip password   NOPASSWORD
Sip contact 192.168.0.228   
Auto connect   NO
Audio quality   
Codec out gain   
Codec inp gain   
Codec inp HPF Hz   
Codec inp preamp   
COM0 baudrate   38400
COM0 data bits   8
COM0 stop bits   0
COM0 parity           1
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0                  NO

Status
Name   Value
Control panel   ON
Radio   ON
Connection status   Disconnected
SIP status   Connect request
Last SIP error   None
RTP/UDP audio status   Disconnected
UDP cmd status   Disconnected
SIP command timeout   0

----------------------------------------------------------------------------



Why they do not connect?
thanks

73 Franco I1FQH

i1fqh@yahoo.it

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #1 on: 2014-02-02, 15:46:53 »
the data you have pasted in is not correct. There some mixup or confusion.

default IP for Control RRC is 192.168.0.227 and for Radio-RRC 192.168.0.228

SIP contact field is only available in control RRC and there should be the IP of the Radio-RRC

check that the header showing Control in the Control RRC and Radio in the Radio RRC if not read this

http://www.remoterig.com/wp/?page_id=1695

/mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #2 on: 2014-02-02, 16:49:16 »
Ok tanks Mike for quick reply

and pse exact serial setting is
On:

Remote
COM 1 - Mode 7

Local
Com 1 - Mode 6

????????????????????????????

73 Franco

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #3 on: 2014-02-02, 17:14:27 »
the settings for com1 doesn't matter. Make it working before bother with com1

/Mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #4 on: 2014-02-02, 23:37:25 »
Ok tnx DONE now I see 1 radio and 1 control (before 2 control)

Tnx very much......

It appears to be working---

last problem (sure not least)

Control switch off remote radio but non on???????

Tnx Franco i1fqh

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #5 on: 2014-02-03, 08:38:22 »
K3 is switched on by a hardware signal in the ACC connector. There should be a cable from Radio-RRC I/O connector to the K3 ACC connector and you need to set Out0 = Connect in the Radio-RRC.

73 de mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #6 on: 2014-02-03, 20:18:35 »
MMMMMMMMMMMMMMMM

tnx Mike for support

Cable is the original supplied and in use..

set of: Out0 = Connect

But remote do not switch on the radio...
Any idea?

Franco i1fqh

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #7 on: 2014-02-03, 20:22:23 »
no that's all which is needed, When pressing the power on button on the control K3, the connection will be setup and the remote K3- will start.

73 de mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #8 on: 2014-02-03, 21:44:24 »
Tnx

"On and off" on remote is done by same cable?

Now i will test the cable connections. (Tested is OK!!)

No particular hardware setup on the board??

Franco i1fqh 

P.S.

All 2 radios are connected but
RADIO STATUS
is
Name   Value
Radio   OFF
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None

why Radio OFF???Radio is ON!
« Last Edit: 2014-02-03, 22:45:14 by i1fqh »

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #9 on: 2014-02-03, 22:27:08 »
The hardware signal is only for power ON. Power off is handled by a data message over the CAT port

Only the cable and the setting for OUT 0 = connect in the Radio-RRC are needed no straps or other things

/mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #10 on: 2014-02-03, 22:59:36 »
The hardware signal is only for power ON.

What I have to do to test if hardware works properly??



 Power off is handled by a data message over the CAT port

OFF is OK!


sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #11 on: 2014-02-03, 23:12:16 »
You  can measure with a volt meter that pin 7 in the ACC connector goes low, but it's open collector so the cable has to be connected to the K3 when you do the measure.If you have bought a new set uf RRC.s the output is tested and OK. Where have you bought it, not from us as far as I can see ? Do you have cables bought from us or elecraft or have you made them by your self ?

/mike

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #12 on: 2014-02-03, 23:49:05 »
Hello Mike

bought new from you on 2012 - serial n.r. 1258 (twin k3 set with all cables.)
Never used (busy with my work) only tested 1 time -----

Tomorrow evening I try to test with a volt meter pin 7

Tnx and good night

73 Franco
« Last Edit: 2014-02-03, 23:57:17 by i1fqh »

i1fqh

  • Newbie
  • *
  • Posts: 15
    • View Profile
    • Email
Re: K3 + K3 and no connession
« Reply #13 on: 2014-02-04, 22:23:08 »
You  can measure with a volt meter that pin 7 in the ACC connector goes low, but it's open collector


Hello Mike g.e.

but pin 7 in the ACC connector as seen on page 207 of the user manual is not in use ... cable use pin 1-8-5

Tnx
Franco i1fqh

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: K3 + K3 and no connession
« Reply #14 on: 2014-02-04, 22:28:03 »
The ACC connector is on the back of the radio

/mike