Messages

2476

Hardware, Cabling, Installations / Re: K3 RTTY

« on: 2011-12-15, 07:51:20 »

The drawing of the cable is correct, but there is a few places in the manual where the description of the I/O connector is wrong. It 's changed in the latest version of the manual which will be released any day. We will just add some new functions

73 demike

2477

Hårdvara, Kablage, Installationer / Re: Reläer på 1216L

« on: 2011-12-13, 16:04:37 »

Nej inte idag i alla fall, det går inte heller att styra dom reläerna annat än via rotor funktionen. är det inte enklare använda radio och NEXA-brytare

Hälsningar

Mikael

2478

Konfiguration av RRC 1258 / Re: ddns remoterig

« on: 2011-12-13, 15:59:33 »

Hej

Det funkar ju att surfa till adressen så registering och uppdatering av dns funkar ju , prova det, så det borde funka i SIP kontakt fältet också. Du har inte fått in nått mellanslag eller nått där ?

Och det är bara "own host name" du skall kopiera till sip kontakt inte passwordet.

Använder du SIP password så skall du använda ditt gamla i båda ändorna.

73 de micke

2479

General discussion forum / Re: Elecraft K3 1258MkIIs Remoterig DRR-Twin is also possible with Kenwood ts-590?

« on: 2011-12-12, 22:12:15 »

The K3 Twin do not use the Kenwood protocol, It's a special protocol only for communication between the Control radio and the Remote radio. We have got the question about TS-590 several times and I have answered that the day we can borrow two 590s we will see what can be done.

73 de mike

2480

Konfiguration av RRC 1258 / Re: ddns remoterig

« on: 2011-12-12, 22:06:21 »

Hej. Det var bara från början vi hade skrivit fel serienummer i databasen. Nu skall det funka med alla. Vad har din burk för serienummer ? vad står det på status sidan om Dynamic DNS status ?

73 de micke

2481

General discussion forum / Re: Remote works fantastic

« on: 2011-12-07, 09:46:30 »

Hi Lee

With the Antenna setup you have in Summit I think you should consider the K3 Twin or Yaesu Twin solution to be able to use a radio which match the Antennas. Both those solution gives the same feeling as with the IC-706 with the front panel.

73 de mike/sm2o

2482

Configuration, RRC 1258 / Re: Remoterig FREE Dynamic DNS service

« on: 2011-12-05, 23:19:05 »

Hi
pse send me a print screen of the dns page and the status page by email to mikael(a)microbit.se

73 de mike

2483

General discussion / Re: Exactly what is wrong!

« on: 2011-12-05, 15:54:28 »

I have mailed you

/mike

2484

Configuration, RRC 1258 / Re: Remoterig FREE Dynamic DNS service

« on: 2011-12-05, 12:20:09 »

We found that we where not accepting serial number lower than 3300. If yours where lower than 3300 that could be the reason. We have fixed that. If you try again and it doesn't work, check the Dynamic DNS status on the Status page and let us know the result

73 de mikel

2485

General discussion / Re: Exactly what is wrong!

« on: 2011-12-02, 17:10:16 »

Maybe there is some differences in timing between different FT-2000. Setup portforwarding for port 23 (telnet) and email me the info we need to connect to your Radio-RRC. We will test on Monday when the software guys are at the office.

73 de mike

2486

General discussion forum / Re: RRC1258 Fails to boot

« on: 2011-12-02, 12:30:08 »

IF the red and yellow stays on the processor never start the main program. Reset the box to Factory default by pressing the Reset button for 30 sec. Connect a serial cable to COM1. Start a terminal program in the PC set to 38400 baud, 8 bit, 1 stopbit, no parity, no handshake. If the bootloader in the box sends some text to the terminal it's possible to upload a new firmware via X-modem. If no text shows you better send the PCB to us.

73 de mike

2487

General discussion forum / Re: Dyndns no longer free?

« on: 2011-12-02, 12:21:32 »

from RRC v2.48 we have introduced our own Dynamic DNS service. It's described in the manual.

73 de mike

2488

General discussion / Re: Exactly what is wrong!

« on: 2011-12-01, 18:15:37 »

Cables are important some times, even in this wireless world. Good luck

/mike

2489

Configuration, RRC 1258 / Re: IC-706mk2g separation cable cw configs and other questions

« on: 2011-12-01, 16:38:18 »

Hi

You must use the pot to disable the sidetone of the IC-706 it's not possible to do from the menu.

I think you have not Enabled the Keyer in the Control-RRC if you do not hear the sidetone from the RRC.

73 de mike

2490

Configuration, RRC 1258 / Re: IC-706mk2g separation cable cw configs and other questions

« on: 2011-12-01, 16:16:41 »

Hi

The sidetone for the Internal CW keyer is generated in the Control-RRC and you should hear it without even switching on the IC-706. If you can't live with the behaviour of the internal keyer without switching on the IC-706 it's not much to do, then you have to use your own keyer. It sounds strange beacuse I have really skilled CW operator friends which have no problem using the internal keyer.

Then when starting to test with the IC-706 remeber to turn down the CW-sidetone with the pot on the side of the IC-706 body. With 80 ms ping time I should set "key delay ms" to 100 ms to start with. Then let somebody else listen to you over the air. You can't listen to the transmission and using the paddles, it's impossible with more than 100 ms delay.

You can use the serial ports for Rotator and loggin, no problem it's just a matter of cables and settings

73 de mike