2371
Allmän diskussion / Re: PTT problem
« on: 2012-04-29, 18:27:27 »
Vi har haft hundratals nedladdningar av de nya versionerna och ingen har rapporterat nått sånt, så jag tror du har nått annat problem
73 de micke
73 de micke
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2372
General discussion forum / Re: Remote Rig Newbie-IC7000 TX audio problem
« on: 2012-04-29, 18:26:05 »
I think you have the red straps placed in wrong positions. The COM0 serial port is also present in the socket, and if you have put a red strap in that position it will give the effect you describe. Check with the manual how you should count, when placing the straps.
73 de mike
73 de mike
2373
Configuration, RRC 1258 / Re: Could you please support the noip.com free DDNS?
« on: 2012-04-29, 18:22:42 »
I Agree with Mitch I don't see any need to support noip, those who want to use noip can setup their router to use it.
73 de mike
73 de mike
2374
Allmänt diskussionsforum / Re: TS-2000 Twin?
« on: 2012-04-29, 18:21:00 »
Jag har aldrig hört talas om den funktionen, men det är väl bara att testa för nån som har 2 st TS-2000, jag har ingen.
/micke
/micke
2375
General discussion forum / Re: Yaesu FT7800/8800/8900
« on: 2012-04-27, 06:09:10 »
All now available version support FT-8800/8900, And all earlier verisions which have the black box.
73 de mike
73 de mike
2376
General discussion forum / Re: Yaesu FT7800/8800/8900
« on: 2012-04-26, 22:27:48 »
I looked at the schematics for the FT-7800, and the electrical connections are the same as for FT-8800/8900 so it's a good chance that it works with FT-7800 also, but we do not have one to test with. The manual are updated with the FT-8800/8900 and the firmware will be released ASAP.
73 de mike
73 de mike
2377
General discussion forum / Re: Yaesu FT7800/8800/8900
« on: 2012-04-26, 21:53:25 »
yes with all black boxes
/mike
/mike
2378
Hardware, Cabling, Installations / Re: Com Port 1 - ready to tackle
« on: 2012-04-26, 07:33:21 »
There is a instruction and cable drawings on the website.
http://www.remoterig.com/wp/?page_id=426
pin config for the com port connectors are shown in the users manual
73 de mike
http://www.remoterig.com/wp/?page_id=426
pin config for the com port connectors are shown in the users manual
73 de mike
2379
General discussion forum / Re: Yaesu FT7800/8800/8900
« on: 2012-04-25, 15:59:55 »
We have now fixed support for FT-8800/8900 and it will be included in next firmware release. The users manual will also be updated with a chapter for FT-8800/8900
73 de mike
73 de mike
2380
General discussion forum / Re: Ts-2000/computer controlvia remoterig
« on: 2012-04-24, 10:19:15 »
Hi
You can install the pc -program and run it without the Remoterig connected direct to the radio to evaluate the software. When connecting the Remoterig system you will get exactly the same functionallity as the Remoterig system only transfer the data and audio, and will not give any other influence on the control of the radio.
73 de mike
You can install the pc -program and run it without the Remoterig connected direct to the radio to evaluate the software. When connecting the Remoterig system you will get exactly the same functionallity as the Remoterig system only transfer the data and audio, and will not give any other influence on the control of the radio.
73 de mike
2381
General discussion forum / Re: FSK audio monitoring
« on: 2012-04-24, 09:13:06 »
I used RTTY yesterday myself and the side tone is there. Have you enabled "Continuous RTP tx" in the Radio RRC I think it need to be set to YES so the audio will not be muted when PTT is "pressed" by the RTTY program.
73 de mike
73 de mike
2382
General discussion forum / Re: Dayton - 2012
« on: 2012-04-23, 20:30:51 »
Yes Remoterig will be at Dayton 2012
I will be at Dayton Hamvention, from Thursday to Sunday. We will not have our own booth but I think it will be a good chance to meet anyway. I will be at HRO booth at least once every day.
73 de mike/sm2o
I will be at Dayton Hamvention, from Thursday to Sunday. We will not have our own booth but I think it will be a good chance to meet anyway. I will be at HRO booth at least once every day.
73 de mike/sm2o
2383
General discussion forum / Re: RR1258 and Green Heron Rotor and Steppir
« on: 2012-04-19, 21:28:00 »
Hi
I have answered this before somewhere.
1. You can not use a splitter to K3 CAT. You should use the RRC:s built in CAT server, the SteppIR should be connected to RRC-Com1 and com1 should be set to mode 6 or 7. See manual.
2. Com1 is occupied by the SteppIR and cannot be used for a rotator in this config.
3. Ok
4. -
If you need to connect more equipment which need to talk to the K3 (antenna switch etc) the splitter should be connected to RRC com1. Nothing are allowed to be connected between the RRC com2 and the K3.
I have answered this before somewhere.
1. You can not use a splitter to K3 CAT. You should use the RRC:s built in CAT server, the SteppIR should be connected to RRC-Com1 and com1 should be set to mode 6 or 7. See manual.
2. Com1 is occupied by the SteppIR and cannot be used for a rotator in this config.
3. Ok
4. -
If you need to connect more equipment which need to talk to the K3 (antenna switch etc) the splitter should be connected to RRC com1. Nothing are allowed to be connected between the RRC com2 and the K3.
2384
General discussion forum / Re: Yaesu FT7800/8800/8900
« on: 2012-04-19, 19:08:49 »
Hi
We have tested with FT-8800/8900 and it doesn't work. When we get some time we will see if something can be done about it.
73 de mike
We have tested with FT-8800/8900 and it doesn't work. When we get some time we will see if something can be done about it.
73 de mike
2385
General discussion / Re: PSK and AFSK
« on: 2012-04-19, 15:54:27 »
Hi
It's not possible to bridge soundcards in Windows (as we are aware of at least) so, you must use one other soundcard (for example the internal ) for the PSK program and connect analog cables to the 1274 dongle.
73 de mike
It's not possible to bridge soundcards in Windows (as we are aware of at least) so, you must use one other soundcard (for example the internal ) for the PSK program and connect analog cables to the 1274 dongle.
73 de mike