2491
General discussion / Re: TS-480
« on: 2011-12-01, 15:53:08 »
Yes if jmp3 is in place and you use a straight cable with wies fro pin 2,3,5,7,8 then pin 7 and 8 will be connected together in the RRC.
73 de mike
73 de mike
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2492
News / New firmware for RRC-1258all. v2.48
« on: 2011-12-01, 15:46:35 »
A new firmware for the RRC is released v2.48.
-New function: Support for Remoterig dynamic DNS.
-New function: Pwr on/off command for Yaesu FT-450/950/2000/5000/9000
The pwr on function was developed to take care of PWR on FT-2000 when controlling it from HamRadioDeLuxe but can probably be useful in other situations also.
73 de mike
-New function: Support for Remoterig dynamic DNS.
-New function: Pwr on/off command for Yaesu FT-450/950/2000/5000/9000
The pwr on function was developed to take care of PWR on FT-2000 when controlling it from HamRadioDeLuxe but can probably be useful in other situations also.
73 de mike
2493
News / Remoterig FREE Dynamic DNS service
« on: 2011-12-01, 15:41:47 »
Since DynDNS has stopped offering free Dynamic DNS Services we have built our own Remoterig dynamic DNS service. This service is for Remoterig and Microbit products only and is of course free. No registration is needed the function is automatic and based on the serial number of the Equipment. The remoterig ddns client is included from firmware version 2.48. The settings needed to activate the ddns function are described in the Users manual version A17.
73 de mike
73 de mike
2494
General discussion / Re: Exactly what is wrong!
« on: 2011-11-30, 17:59:27 »
The pwr on/off function has nothing to do with the pc client or setup of HRD.
It's sent when SIP ocnnection is up, independent of the control side. It will send the message even if you use box to box solution. You should use radio mode 4 or 10 and enable the function under advanced settings.
The problem with old PC softwares accepting virtual com ports has nothing to to with if RTS/DTR etc. is used or not, the problem is on a totally different level.
I assume you have coonected pin 7 and 8 and set jmp 3 in place.
73 de mike
It's sent when SIP ocnnection is up, independent of the control side. It will send the message even if you use box to box solution. You should use radio mode 4 or 10 and enable the function under advanced settings.
The problem with old PC softwares accepting virtual com ports has nothing to to with if RTS/DTR etc. is used or not, the problem is on a totally different level.
I assume you have coonected pin 7 and 8 and set jmp 3 in place.
73 de mike
2495
Allmänt diskussionsforum / Re: Radiodelen för Nexa
« on: 2011-11-30, 13:21:16 »
Hej
Vi kan inte rekommendera att man gör det, det sätter hela CE märkning på spel, så det får du göra helt på eget bevåg i så fall.
/mikael
Vi kan inte rekommendera att man gör det, det sätter hela CE märkning på spel, så det får du göra helt på eget bevåg i så fall.
/mikael
2496
General discussion forum / Re: RX Audio dropout depending on Sip contact setting
« on: 2011-11-29, 11:35:25 »
DynDns names mostly does not work at all inside a LAN, and if it works it's difficult to determine how the routing is done in your router. Use IP addressing inside the LAN to be sure.
When using WLAN for VoIP switch of the automatic switching between 802.11 a/b/g etc some access points and routers periodically test the different modes and it will result in a audio dropout during the test.
73 de mike
When using WLAN for VoIP switch of the automatic switching between 802.11 a/b/g etc some access points and routers periodically test the different modes and it will result in a audio dropout during the test.
73 de mike
2497
Allmänt diskussionsforum / Re: 1216L Rotator controller A/D problem ?
« on: 2011-11-25, 23:50:10 »
Hej
Det som går att göra är gjort i version 1.24 som publicerats idag. Tyvärr så stödjer A/D omvandlaren bara i teorin 16 bitar. Om man studerar manualen så står det också där det interna noiset i A/D så stort att man inte har någon som helst nytta av 16 bitar. Men som sagt vi har gjort dessa saker programmerbar i alla fall.
73 de micke
Det som går att göra är gjort i version 1.24 som publicerats idag. Tyvärr så stödjer A/D omvandlaren bara i teorin 16 bitar. Om man studerar manualen så står det också där det interna noiset i A/D så stort att man inte har någon som helst nytta av 16 bitar. Men som sagt vi har gjort dessa saker programmerbar i alla fall.
73 de micke
2498
News / New firmware v1.24 for the Webswitch released
« on: 2011-11-25, 15:56:30 »
New user requested functions are implemented.
These are the Radio related functions:
- Rather heavily modified analogue rotator support. It’s now possible to select input voltage range either between 0-2.55V or between 0-5.10V(was used before), as well as resolution from 8-15 bits. Note that the A/D’s accuracy is only 8 bits so a higher resolution isn’t necessary better. 10 bits was used in previous versions.
- Added support for Idiom Press rotator controllers.
- Made it possible to activate more than one relay simultaneous when using the automatic antenna switch feature. Also added a 5 minutes time out which will inactive all relays if frequency information stops coming.
Download it here
http://www.remoterig.com/wp1216/?page_id=162
73 de mike
These are the Radio related functions:
- Rather heavily modified analogue rotator support. It’s now possible to select input voltage range either between 0-2.55V or between 0-5.10V(was used before), as well as resolution from 8-15 bits. Note that the A/D’s accuracy is only 8 bits so a higher resolution isn’t necessary better. 10 bits was used in previous versions.
- Added support for Idiom Press rotator controllers.
- Made it possible to activate more than one relay simultaneous when using the automatic antenna switch feature. Also added a 5 minutes time out which will inactive all relays if frequency information stops coming.
Download it here
http://www.remoterig.com/wp1216/?page_id=162
73 de mike
2499
General discussion / Re: Exactly what is wrong!
« on: 2011-11-25, 15:34:27 »
Hi
there is a new firmware version with support for Yaesu pwr on/off. The function is activated under the Advanced menu. I hope it will solve your problems.
73 de mike
http://www.remoterig.com/firmwares/RRC-1258-CRC_v2.47_2011-11-25.zip
there is a new firmware version with support for Yaesu pwr on/off. The function is activated under the Advanced menu. I hope it will solve your problems.
73 de mike
http://www.remoterig.com/firmwares/RRC-1258-CRC_v2.47_2011-11-25.zip
2500
Hardware, Cabling, Installations / Re: CW&PTT via USB from WinTest ?
« on: 2011-11-25, 07:50:52 »
If you activate the "PTT activated by keyer" the PTT is activated before the "Key delay ms" time so if you set a key delay time you get the function you need plus you use the buffer for keying and get a more robust keying signal. It works in the same way even if you use an external keyer connected to the "straight key" input with the keyer activated.
When switching a serial port to USB you turn off the RS-232 port at the same time. You can not use both USB com2 and RS232 com2 at the same time.
73 de mikel
When switching a serial port to USB you turn off the RS-232 port at the same time. You can not use both USB com2 and RS232 com2 at the same time.
73 de mikel
2501
Hardware, Cabling, Installations / Re: CW&PTT via USB from WinTest ?
« on: 2011-11-24, 20:34:02 »
Hi, what is the main problem ? Wwith the K3 in CW and VOX no PTT signal is needed. If you do not want to use VOX and want PTT signal when using the internal keyer you just need to activate "PTT activated by keyer" under the keyer settings in the Radio-RRC.
73 de mike
73 de mike
2502
Hardware, Cabling, Installations / Re: ICOM IC-7000 ANYBODY DONE THIS RADIO YET?
« on: 2011-11-23, 23:30:12 »
To configure the IC-7000 you should look in the ICOM in general chapter in the manual. It's like all other ICOM:s. The IC-706 chapter describes the IC-706 with separated control panel and it's not possible with the IC-7000.
73 de mike
73 de mike
2503
General discussion / Re: Exactly what is wrong!
« on: 2011-11-22, 20:26:13 »
We tested today with HRD and found that the creator of HRD has forgot to include the Power on command in FT-2000 mode. You can test to setup HRD in FT-950 mode then the FT-2000 will start up. Of course there will be other problems using it in FT-950 mode.
We will make a new setting where you can tell the RRC to send the "Pwr On" command automatically when you connect in mode 4.
73 de mike
We will make a new setting where you can tell the RRC to send the "Pwr On" command automatically when you connect in mode 4.
73 de mike
2504
Hardware, Cabling, Installations / Re: No sound TX on PSK
« on: 2011-11-22, 18:14:06 »
You must describe what is not working. If you activate "Continuous RTP" in control end audio is always go from Control-RRC to Radio-RRC. You can test in SSB mode to activate VOX in the radio and shout in the Microphone. If the audio is not comming through the cabling are not OK. If the audio is there but the the transmission is cut in the tail you must change the connections so you PTT the Control-RRC, thats always better then the PTT will be in sync with the transmission.
73 de mike
73 de mike
2505
Hardware, Cabling, Installations / Re: No sound TX on PSK
« on: 2011-11-21, 19:10:47 »
Hi
If you use the software to send PTT commands via the CAT interface, the control RRC do not get the information about change to transmit mode. So you either need to connect to the PTT input of the COntrol-RRC or set "continous RTP" on to let the audio go from Control-RRC to Radio-RRC all the time.
73 de mike
If you use the software to send PTT commands via the CAT interface, the control RRC do not get the information about change to transmit mode. So you either need to connect to the PTT input of the COntrol-RRC or set "continous RTP" on to let the audio go from Control-RRC to Radio-RRC all the time.
73 de mike