Messages

2611

General discussion / Re: PC client Software and CW

« on: 2011-05-02, 20:32:28 »

Hi

"Bug key" should be off, and the key line should be connected to the straight key input, sidetone should be activated and VOX should be activated

73 de mike

2612

General discussion / Re: Remote rig problems continued

« on: 2011-05-02, 18:38:04 »

Hi
If it works on your local LAN the hardware is ok and you are almost there. Remember that dyndns can not be used at the local LAN.

At the radio QTH setup the router to forward ports 80 (tcp),5060 (udp),11000 (udp),12000 (udp) to the ip of your RRC. Or even better set the Radio-RRC as DMZ host. Be sure that SIP ALG is NOT activated if you have a parameter like that. If you have IP-telephony in either end change the SIP-port from 5060 to something else, in both ends.

The extern ip should NOT be set anywhere, The dyndns adress should be used as SIP-contact at the Control RRC when you move the equipment to the radio-QTH.

73 de mike

2613

General discussion / Re: PC client Software and CW

« on: 2011-05-02, 14:54:47 »

Hi

Yes you must activate VOX or SEMI BREAK IN and Sidetone in the Radio.

I use TS-480 my self and it works

73 de mike

2614

General discussion forum / Re: 706 cable problem

« on: 2011-05-01, 14:04:19 »

Hi

It sounds like something is wrong with the cable, check with an ohm meter, that there is no short circuit between the different wires.

73 de

2615

General discussion forum / Re: TS480 front panel is off

« on: 2011-05-01, 13:58:22 »

hi

email me ip-address and login so I can test from here

73 de mike

2616

News / New software for the RRC-Micro PC client released (v1.2.0)

« on: 2011-04-27, 16:27:38 »

News: Keyboard CW support ( Needs RRC-1258 v2.37)
Changed: Speaker drop downs now only shows speaker devices
Changed: Mic drop downs now only shows mic devices
Fixes: Some other small fixes are done.

2617

News / New firmware for RRC-1258-all v2.37

« on: 2011-04-27, 16:25:04 »

There is a new version v2.37 available for the RCC:s

- Supports Keyboard CW from PC-Client

http://www.remoterig.com/firmwares/RRC-1258-CRC_v2.37_2011-04-26.zip

73 de mike

2618

News / New firmware for RRC-1258-all v2.36

« on: 2011-04-27, 16:23:58 »

There is a new version v2.36 available for the RCC:s

- The problem with firmware update via USB from some computers are now finally solved.
– Fixed  a bug in the SIP-busy handling.
– Fixed a bug in USB-Cat function introduced in v2.35 which caused reset in some situations.


73 de mike

2619

News / New firmware for RRC-1258-all v2.35

« on: 2011-04-27, 16:22:13 »

There is a new version v2.35 available for the RCC:s

- The USB Interface can be used for the CAT control. ( eliminate the need for RS-232 port on Laptops).
– The RRC now handles shift between Yaesu Twin and RRC-Micro automatically in mode 10. ( without need for changing settings).
– Better busy handling, prevent unwanted  double connections from inside the same router. ( need v.1.1.3 of RRC-Micro).
– No bootloader text on COM1 if Bootloader 1.9 is used.


73 de mike

2620

General discussion forum / Re: Same MAC address

« on: 2011-04-26, 06:50:07 »

Hi

That should not be possible, but is easy to fix if you send me the real serial number from the sticker inside the boxes

73 de mike

2621

General discussion forum / Re: TS480 front panel is off

« on: 2011-04-25, 22:05:09 »

If everything works besides the PTT and Mic audio then the straps are probably missplaced or broken. Check the placement against the manual, check that you have the box the same way as on the picture in the manual. If straps are placed OK check them with an ohm meter, they can have been broken when pressed into the socket, even if it's not visible. There is no settings that can be wrong, only straps or the Mic-cable from Radio-RRC to Radio.

73 de mike

2622

Hårdvara, Kablage, Installationer / Re: Yaesu FT-857 (Inte klar än)

« on: 2011-04-25, 10:05:59 »

Det är möjligt att det kan gå att göra som du säger, jag har själv tänkt i de banorna, men frågan är om det är värt arbetet. Skulle det finnas dokumentation på protokollet mellan front och radio så man visste säkert att det man gör löser problemet då vore det ju enklare. Vi är ju ett företag så vi måste hela tiden väga arbetsinsats mot vad vi tror det kan ge tillbaka tyvärr.  73 de mikael

2623

General discussion / Re: RCC control output

« on: 2011-04-25, 10:00:19 »

Hi

There is no way to control the outputs from the pc-client. But you can set an IO pin to be activated automatically when you connect or set it in on/off mode. In on/off mode you can browse to the Radio-RRC and activate and deactivate the IO pin direct from the webpage. Maybe you have to upgrade to a later firmware to get this functions.  73 de mike

2624

Hardware, Cabling, Installations / Re: RRC-radio no power LED

« on: 2011-04-21, 20:19:06 »

The RRC:s are extremly tolerant and stand against almost everything but thunderstorms. Units comming back for repair is extremly rare. I don't have a box with me so I can check what component you are talking about, but it's probably the automatic fuse. Something is consuming to much power. Remove all cables and only connect the pwr cable. If you still have the problem you have to send it in for repair.


73 de mike

2625

General discussion forum / Re: TS480 front panel is off

« on: 2011-04-21, 20:09:52 »

A ts-480 with detachable frontpanel should be used in mode 5 and there should not be a connect button on the status page.The connect and disconnect are controlled automatically from the PWR on button on the control panel. If nothing happens when pressing the pwr on button your cable is wrong or you have not set the baudrate to 57600 so the RRC can not recognize the power on command.

73 de mike