Messages

1

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: Today at 16:11:27 »

The only option is to setup a VPN from radio site av to control site. As SL is unlimited data it's possible, You can use a SMS switch to active the link remotely also

Mike

2

Configuration, RRC 1258 / Re: TS-590S Twin Baud rate

« on: 2024-11-09, 19:25:53 »

You can use whatever baudrate you want but you have to set the CAT baudrate in the Radios and the Remoterig to the same baudrate. Never heard that 19200 is to slow I think the problem is high latency internet connection not the baudrate

73 de mike

3

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-09, 19:22:54 »

Hi

Starlink standard plans cannot be used at the Radio end as they use CGNAT, Only business plans with fixed IP can be used, but they are expensive

73 de mike

4

Allmänt diskussionsforum / Re: Remoterig Kenwood TS480 through mobile router TPlink Archer MR600

« on: 2024-10-10, 14:00:09 »

bra början, då kan du ta ut export settings(html) filer från bägge boxarna och maila till support@remoterig@com så får jag kika på dem

/micke

5

Allmänt diskussionsforum / Re: Remoterig Kenwood TS480 through mobile router TPlink Archer MR600

« on: 2024-10-10, 12:52:09 »

Har du kollat att du inte har CGNAT?
http://www.remoterig.com/wp/?page_id=3494

73 de micke

6

General discussion forum / Re: AS-1289 Cannot update firmware

« on: 2024-09-29, 19:55:52 »

I have emailed you instructions the same day
Mike

7

General discussion forum / Re: AS-1289 Cannot update firmware

« on: 2024-09-24, 11:11:07 »

Hi

There is no AS-1216H, it's WS-1216H and RC-1216H

if you email me a printscreen of the info page, I will send you a fix

support@remoterig.com

73 de mike

8

General discussion forum / Re: RRC not connecting

« on: 2024-09-20, 09:39:54 »

Hi

Send export settings (html) files to support@remoterig.com

73 de mike

9

General discussion forum / Re: rc 1216 via ip

« on: 2024-09-02, 14:22:06 »

i don't know what you mean by
"My rs232 of the ts2000 is occupied by CCR in the tower."

if you mean that you allready have connected the Radio-RRC to the Radio-CAT port all is OK

The AS-1289 talks to the Radio via the CAT cable, the RRC does not know anything about the radio, it only transfer data

but if you already us com 2 for controlling the radio all is OK as the AS-1289 can share the connection with the control software.

So if you set Radio-RRC settings with the correct ip nummer (radio-RRC) and correct port(13010)  and serial setting to 9600 it should work and on the main page you should see the "Current frequency" following the radio

73 de mike

10

General discussion forum / Re: rc 1216 via ip

« on: 2024-09-02, 13:54:25 »

Kenwood (IF) is what you normally use if you want the AS-1289 to ask for the frequency from the radio.
remeber that you need to have a CAT cable from the Radio-RRC com2 to the Radio CAT port
com 2 should be set to mode 4 and that all three set to the same baudrate

73 de mike

11

Configuration, RRC 1258 / Re: Settings for Winkey use only?

« on: 2024-09-01, 18:47:28 »

Hi

compared to the bandwidth that the 6600 needs the Remoterig audio is negligible, so you can use audio quality 2 , no data is sent so it's only the audio which needs bandwidth

73 de mike

12

Konfiguration av RRC 1258 / Re: RRC-1258 MkII

« on: 2024-08-17, 20:32:13 »

Hej

Du måste nog vara mer specifik i din frågeställning om man skall kunna hjälpa dig.

Det finns ingen standard inställning som funkar för alla radio och alla Nätverksanslutningar

Att du bytt dator innebär normalt inte att några ändringar i Remoterig krävs

Om du bytt Routern på Radiosidan så måste portforwarding sättas upp i den nya routern. Ev måste IP addressen ändras i Radio-RRC om den nya Routern inte använder samma LAN IP-addresser

73 de micke

13

General discussion forum / Re: Latency and Starlink

« on: 2024-08-17, 20:24:39 »

Hi

This has not been an Issue for many years as Internet latency has imporved.

I found a answer I gave you in 2015

We do not have any documentation about it, but some where between 200-300 ms I think the limit is.

Remember that ordinary Starlink plans do not include public IP so you must have a business plan in the Radio end if you want to use Starlink

73 de mike

14

General discussion forum / Re: Webswitch 1216H lost user and password

« on: 2024-07-27, 17:13:58 »

There is no pdf manual only instructions at www.webswitch.se

There is no default password. The password settings are blank when delivered.

if you have the unit public reachable it can be robots which have set the password it has happened many times so always set  password.

/mike

15

General discussion forum / Re: Webswitch 1216H lost user and password

« on: 2024-07-27, 16:18:17 »

It's a standard USB cable . A to Mini

Mike