Messages

31

General discussion forum / Re: Trouble getting set up

« on: 2024-01-13, 22:21:27 »

If the units have been used in another environment I would guess that SIP contact in the Control-RRC is not set correct, at the current LAN it should be set to 192.168.10.102 (eg the ip of the Radio-RRC) I suggest you download the manual and go through the step by step setup.

73 de mike

32

Hardware, Cabling, Installations / Re: Set up validation for a totally new user

« on: 2024-01-12, 17:33:07 »

Yes
you can use FT-991, see manual page 176 chapter Yaesu in General (FT-2000)

73 de mike

33

General discussion forum / Re: K3/0 connection to K3

« on: 2024-01-10, 20:02:31 »

If you can login to the router, check that SIP ALG is OFF if it has a SIP ALG setting

73 de mike

34

General discussion forum / Re: K3/0 connection to K3

« on: 2024-01-10, 19:46:54 »

Hi

There is no difference working from France or within the US. But if you are using a Hotel Wifi or a public Wifi they may have blocked ports, that's quite common

73 de mike

35

General discussion forum / Re: No connection to the server

« on: 2024-01-05, 17:52:16 »

No DDNS server problem

73 de mike

36

General discussion forum / Re: WiFi - How I finally have reliable remote CW keying with my RRC-1258 pair

« on: 2023-12-28, 11:54:50 »

Hi

You did not say anything about the most important setting to use CW. The "Key Delay ms" if you increase the buffering by increasing Key Delay, CW works OK in most situtations. With Key Delay =0 you need an extremly good Internet connection to make it work

73 de mike

37

General discussion forum / Re: Everything works except on 21mhz

« on: 2023-12-27, 10:28:17 »

Hi

Remoterig has no idea about what band you are using. Remoterig does not intrepret or change any data either, just transfer it.

So your problem is with the radio and not with Remoterig

73 de mike

38

General discussion forum / Re: Connect Bug/vertical key

« on: 2023-12-18, 18:31:39 »

Yes

Activate keyer on the keyer setup page. Paddles are connected to the PAD jack. An external keyer or a straight key is connected between GND and IN0 in the I/O jack on the back ( see manual for details)

73 de mike

39

General discussion forum / Re: Trying to install second RRC Box

« on: 2023-12-10, 21:25:50 »

It works if it's done correct. I have 4 sets my self in use

/Mike

40

General discussion forum / Re: Trying to install second RRC Box

« on: 2023-12-10, 20:37:54 »

Yes, and setup the same ports in the second Control-RRC

Mike

41

General discussion forum / Re: Trying to install second RRC Box

« on: 2023-12-10, 20:02:17 »

Hi

Just setup unique portnumbers for each RRC pair. And setup corresponding portforwardilngs for each port in the radio QTH router

73 de mike

42

General discussion forum / Re: Headphones Mono

« on: 2023-12-07, 19:42:17 »

Hi

It depends on how you have setup the radio-RRC. if Audio dual RX = yes then you need to provide left and right audio to the Radio RRC to get audio in both ears (middle ring,tip). If audio dual-rx = No then you get audio in both ears when providing mono audio to the tip. If you have a dual rx radio there is often internal settings in the radio also about how to provide the audio

73 de mike

43

General discussion forum / Re: Trouble getting set up

« on: 2023-12-01, 09:39:24 »

you could have attaced a printscreen of the find Devices window

/mike

44

General discussion forum / Re: Modes 6 & 7 (CAT to COM2) doesn't support all CAT commands?

« on: 2023-11-23, 21:29:44 »

Hi

I don't know what you want to do, but to clarify, the sharing to com1 is meant to be used in the radio end for PAs or Antenna switches etc to folllow band switching etc, and in control end for using a log program or WSJT-X etc. That has beed working without any complains for about 10 years.

73 de mike

45

Configuration, Webswitch 1216H / Re: webinterface

« on: 2023-11-19, 14:13:54 »

yes you can set password on the IP-settings page

73 de mike